Vulcan appliance service for Greater Houston commercial kitchens.
- Fault found before any price
- One fixed price you approve
- 90-day parts warranty
Phones answered now
- 1You callany hour
- 23-hour windowagreed with you
- 3Fixed pricebefore any work
Free to request · 3 steps
Request a repair appointment
Takes about a minute. There is no charge to submit a request.
- Diagnosis
- The cause is identified before any price is given
- Approval
- One fixed price, and work begins only with your consent
- Hours
- Our phones are answered 24 hours a day
- Warranty
- Parts warranted for 90 days, labor for 30
Commercial
Vulcan equipment our technicians service
Common Vulcan failure points
- Pilot or spark ignition faults on burners
- Thermostat or safety valve faults
- Blocked burner ports and uneven flame
- Fryer high-limit trips
- Scale in steamer water systems
The line-up
The Vulcan line-up, unit by unit
Vulcan is one of the longest-established names in American commercial cooking and is part of the ITW Food Equipment Group. Its equipment is found on restaurant lines, in institutional kitchens and in catering operations.
| Range & Stove | Vulcan restaurant ranges combine open burners, griddle plates or hot tops with standard or convection ovens in the base. |
|---|---|
| Oven | Vulcan convection ovens are built for continuous use in baking, roasting and banquet production, in gas and electric versions. |
| Cooktop | Vulcan griddles, charbroilers and hot plates are configured to sit in a cooking line, often on stands or equipment tables. |
Vulcan installation and access
Vulcan equipment sits beneath a ventilation hood on a commercial line, typically on casters with a flexible gas connector and a restraint cable. Our technicians check that the connector and restraint are in sound condition before moving a unit away from the wall. Work on the line is coordinated with kitchen staff so adjacent equipment can remain in use where it is safe.
Common Vulcan faults and what we check
- A standing pilot will not stay litRange & Stove
- The pilot orifice, thermocouple and drafts from the hood or nearby doors are examined, as a weak or deflected pilot flame fails to hold the safety open.
- Product browns on one side of the convection ovenOven
- The blower motor and wheel, door seal and thermostat calibration are checked, since uneven air movement shows up quickly on sheet trays.
- The griddle plate has cold zonesCooktop
- Burner condition, manifold gas pressure and each zone's thermostat are tested across the plate.
- Open burners show a lazy yellow flame and leave sootRange & Stove
- Partly blocked ports, air shutter adjustment and supply pressure are investigated in turn.
Looking after Vulcan equipment between visits
- 01Boil out or scrape burner ports and clean grates on a regular schedule.
- 02Keep the hood filters clean so heat and grease do not build up over the line.
- 03Inspect flexible gas connectors and restraint cables whenever equipment is moved.
- 04Have oven and griddle thermostats checked periodically for consistent results.
Commercial equipment
Service notes for Vulcan equipment
Vulcan manufactures cooking equipment for commercial kitchens. Typical repairs include a pilot that will not stay lit, which points to a failed thermocouple or thermopile; a gas valve or thermostat no longer holding calibration; a fryer that trips its high-limit control; and a convection fan that no longer runs.
- Commercial gas ranges
- Fryers
- Griddles and charbroilers
- Convection ovens
- Steamers
Safe checks to make before calling
- • A pilot that repeatedly goes out is usually caused by the thermocouple, which our technicians can normally replace during the same visit.
Technical notes
What Vulcan repairs involve
Vulcan commercial ranges, stoves, ovens and cooktops, the heavy gas equipment at the center of many restaurant lines, are repaired by our technicians.
Vulcan manufactures commercial cooking equipment, among it ranges, fryers, griddles and convection ovens, intended for kitchens in service throughout the day. Vulcan ranges and ovens typically need thermostats, gas valves, pilot assemblies, igniters or door gaskets, and the equipment is engineered to be rebuilt in stages rather than discarded. With commercial gas equipment our technicians close the supply at the shut-off valve before any work begins and leak-test each disturbed joint before the appliance is returned to service.
Questions
Questions about Vulcan repair
Is older Vulcan equipment worth repairing?
Often it is, because valves, pilots, thermostats and burners are replaceable individually. Our technicians weigh the condition of the body and manifold before recommending repair.
What if the problem is in the building's gas supply?
If the fault lies in the supply or connection rather than the appliance, our technicians leave the equipment shut off and explain the situation to the client. Correcting building gas piping falls outside appliance service.
Arrange Vulcan service
Tell us whether your Vulcan uses standing pilots or spark ignition when you phone.