Jump to main content

Appliance repair across Greater Houston

Whirlpool logo

Whirlpool appliance service in Greater Houston homes.

Whirlpool appliances are conventional and quick to test, which keeps diagnosis straightforward. A technician confirms the fault where the appliance stands and then gives a single figure that you approve before any part is fitted.
  • Fault found before any price
  • One fixed price you approve
  • 90-day parts warranty

Free to request · 3 steps

Request a repair appointment

Takes about a minute. There is no charge to submit a request.

Prefer to call?(832) 476-8009
Step 1 of 3: Appliance and fault

Appliance and fault

01Which appliance needs attention?
02What is it doing?Select an appliance first and its common faults will appear here.
Diagnosis
The cause is identified before any price is given
Approval
One fixed price, and work begins only with your consent
Hours
Our phones are answered 24 hours a day
Warranty
Parts warranted for 90 days, labor for 30

Mass Market

Whirlpool appliances our technicians service

Common Whirlpool failure points

  • Drive coupler wear on direct-drive top-loading washers
  • Cycles halted by a faulty lid switch or door switch
  • Clogged drain pump
  • Bad defrost heater or defrost thermostat
  • A tripped thermal cutoff in the dryer, usually caused by a restricted vent

Error codes

Whirlpool error codes explained

Whirlpool codes, grouped by appliance. A code shows where testing starts, not which part failed; we check it on your unit first.

  • Cabrio and agitator top-loaders
  • Duet front-loaders
  • French-door and side-by-side fridges
  • Gold series dishwashers
  • Gas and electric ranges

Whirlpool washer

F8E1 / LF
The washer is filling too slowly. Check the supply tap, the inlet screens and the water inlet valve.
F9E1 / Ld
The washer is draining too slowly. Check the pump and its filter, and look for a kinked drain hose or a hose inserted too far into the standpipe.
F5E2
The front-loading door lock is not engaging.
F7E1
The control cannot detect motor speed. The drive belt, the motor or the motor control board may be responsible.
rL
Remove load: the washer found clothing or water in the drum at the start of a cleaning cycle.

Whirlpool dryer

AF
The dryer has detected restricted airflow. Inspect the lint screen, the full vent run, and any part of the duct that may have been crushed.
F22 / F23
The exhaust thermistor is reading as an open circuit (F22) or a short circuit (F23).

Whirlpool oven

F3E1
The sensor that measures oven temperature is reading as an open or short circuit.
F1E1
The control board has reported an internal fault.

Safe checks to make before calling

  • • A slow-drain code can be caused by a drain hose inserted too deeply into the standpipe, which siphons water out and misleads the control.
  • • An AF code on the dryer almost always indicates a vent problem. Because a restricted vent is a fire hazard, have it cleaned before drying another load.

Technical notes

What Whirlpool repairs involve

We look after Whirlpool washers, dryers, refrigerators, freezers and dishwashers, and the brand's ovens, ranges, stoves, cooktops and microwaves as well.

A Whirlpool direct-drive top-load washer most often fails at the drive coupler, the lid switch or the drain pump, and testing those in a logical sequence frequently spares the need to dismantle the entire cabinet. A Whirlpool dryer is a simple, durable machine; when it stops producing heat, our technicians first look for a restricted vent and a tripped thermal cut-off, and only then turn to the heating element. Maytag, KitchenAid, JennAir, Amana and Roper are all Whirlpool brands, and a large share of components and service procedures apply across those names, which generally makes parts more available and less costly than the badge implies.

Whirlpool components and the platform behind them

Whirlpool engineers the shared platform behind its own family of brands, so a Whirlpool model is often the reference design for its Maytag, Amana or Roper equivalent, and its part numbers and service documentation are the most complete in the family.

Questions

Questions about Whirlpool repair

What does the F8E1 / LF code on a Whirlpool washer indicate?

The washer is filling too slowly. Check the supply tap, the inlet screens and the water inlet valve.

What does the F9E1 / Ld code on a Whirlpool washer indicate?

The washer is draining too slowly. Check the pump and its filter, and look for a kinked drain hose or a hose inserted too far into the standpipe.

What does the F5E2 code on a Whirlpool washer indicate?

The front-loading door lock is not engaging.

Arrange Whirlpool service

Tell us whether an older Whirlpool is flashing lights or a newer one shows a code such as F8E1 or AF.

Call, any hour(832) 476-8009Book on the web