Cooktop repair in Houston, gas, radiant glass and induction.
- Fault found before any price
- One fixed price you approve
- 90-day parts warranty
Phones answered now
- 1You callany hour
- 23-hour windowagreed with you
- 3Fixed pricebefore any work
Free to request · 3 steps
Request a repair appointment
Takes about a minute. There is no charge to submit a request.
- Diagnosis
- The cause is identified before any price is given
- Approval
- One fixed price, and work begins only with your consent
- Hours
- Our phones are answered 24 hours a day
- Warranty
- Parts warranted for 90 days, labor for 30
- 1–2 hours
- Usual duration of a visit
- 30
- Cooktop faults documented
- 31
- Manufacturers serviced
- 24/7
- Phones answered
Cooktop problems
Cooktop faults by type
Pick the symptom. Gas, radiant and induction cooktops fail differently, and each card says which type it applies to.
Single burner not heatingEvery position on the cooktop heats normally except one. Since the neighboring burners or elements work, the household gas or electrical supply can be ruled out, and attention turns to the components serving that one position.
Usual causes
- An open radiant element or a burnt-out coil element
- A failed infinite switch for that position
- Burner ports blocked by spilled food
- A cracked spark electrode on a gas burner
- A failed induction coil or a faulty section of its power board
What we do
Where the design permits, our technician exchanges the suspect element or burner with a position known to work. If the fault moves with the part, the part is at fault; if it stays, the control is. After that, each suspect component is tested on its own, and nothing is replaced unless it has been shown to be defective.
Gas burner will not lightThe igniter clicks without producing a flame, or makes no sound at all. Spilled liquid commonly wets the igniter or seals the burner ports. If every burner goes quiet together, the fault more likely lies in the spark module that serves all of them.
Usual causes
- A burner cap sitting off its seat
- A wet or cracked igniter electrode
- Burner ports clogged with food residue
- A failed spark module
- A closed gas supply valve
What we do
Our technician removes the burner head and cap, clears the ports and inspects the electrode for its correct gap and for cracks in the porcelain. If a spark still does not appear, the ignition switch and spark module are tested in turn. Whichever part is defective is renewed, after which our technician lights every burner in turn to confirm dependable ignition.
Gas odor near the cooktopA faint odor for a moment while a burner catches is not unusual. An odor that persists, or that is present while every knob is off, is a warning sign. When the odor is strong, do not touch light switches or appliances; get everyone out of the home first, and only once you are well away from the building should you phone 911 or the gas utility.
Usual causes
- A valve leaking around its stem
- A loose fitting at the gas manifold
- Gas flowing to a burner that has failed to light
- A damaged flexible connector
What we do
Our technician checks each joint, valve and connector with an electronic gas detector and a soap solution. Any leaking fitting is tightened or replaced, and the cooktop remains out of service until the complete appliance passes a leak test.
Cracked glass cooking surfaceA crack in a glass or ceramic top opens a path for spills to reach the elements and wiring below. Hairline cracks tend to lengthen with repeated heating. Avoid using the damaged zone until the surface has been examined.
Usual causes
- A heavy pot dropped onto the glass
- Cold liquid striking a hot surface
- Stress from an uneven installation
- Sugar spills burned into the surface
What we do
We examine the crack and inspect the elements beneath for heat or liquid damage. A replacement glass top designed for your model is then fitted, and the elements and wiring are checked once again after installation.
Igniter keeps clickingClicking continues after the flame is established, or starts even with every knob in the off position. A boil-over or a wet cleaning cloth is often responsible, and the noise usually ends as the parts dry. If it persists, one of the spark switches has probably stuck.
Usual causes
- Moisture inside a spark switch
- A worn or stuck spark switch
- A misplaced burner cap preventing the flame from being sensed
- A spark module fault on models with automatic reignition
What we do
Our technician dries the surrounding area and reseats every cap, then disconnects the switches one at a time to identify the one that is shorting. That switch, or the spark module where it is responsible, is replaced so the igniters stay silent whenever the burners are off.
Flame too low on highThe flame stays small even at the highest setting, and boiling water takes much longer than it should. A weak flame on one burner usually points to a blocked port or orifice. Weakness across all burners suggests a regulator or supply pressure problem.
Usual causes
- A clogged burner port or orifice
- A failing pressure regulator
- An orifice sized for the wrong gas, natural or propane
- Low supply pressure
What we do
We clean the ports and orifice of the affected burner and measure gas pressure at the cooktop regulator. A problem on one burner is local, while a problem on all of them traces back to the regulator or supply. A faulty regulator or incorrect orifice is replaced, and flame height is confirmed at every position.
Yellow or orange flameProperly mixed gas burns mostly blue. A yellow or sooty flame indicates incomplete combustion, which marks cookware with soot and generates more carbon monoxide than a clean flame.
Usual causes
- Dirty burner ports
- An air shutter out of adjustment
- A misaligned burner cap
- An orifice set up for a different gas type
What we do
Our technician cleans the burner, adjusts the air shutter where the model provides one and confirms that the orifice matches the gas supplied to your home. The flame is then observed at every setting before the visit ends.
Electric element stays coldOne element on a coil or radiant cooktop no longer warms. On a coil model, you can try moving it to another socket of the same size to see whether the element itself has failed. On a glass model, the element beneath the surface may have broken.
Usual causes
- A broken element coil
- A failed infinite switch
- A burnt coil receptacle
- An open limiter on a radiant element
What we do
We test the element and its switch with a meter and inspect the terminals for heat damage. Our technician renews only the defective item and then runs the position at full heat to verify the result.
One induction zone not heatingA single induction zone refuses to heat even with suitable cookware, while the remaining zones perform normally. This pattern usually indicates a failed coil or a fault in the section of the power board that drives it.
Usual causes
- A failed section of the power board
- A damaged induction coil
- A faulty pan detection sensor
What we do
Our technician runs the built-in diagnostic routine and measures the outputs of the coil and power board. Once the defective coil or board has been renewed, we heat a magnetic pan on that zone to verify the repair.
Touch controls unresponsive or erraticThe touch panel ignores input, reacts with a delay or activates zones without being touched. Water, grease or cleaning product on the glass can easily interfere with touch sensing.
Usual causes
- Moisture or residue on the touch panel
- The control lock engaged
- A failed touch control board
- A loose ribbon cable
What we do
We clean and dry the glass around the controls and make sure the lock is not engaged. Next, our technician checks the ribbon cable connection and measures the touch board. If the board proves defective it is renewed, and each zone and function is operated before the visit ends.
Uneven heating across the panYou may notice food browning only around a circle, or a pan that runs noticeably hotter on one side. Warped cookware is a frequent cause. On a radiant model, a section of the element may have stopped glowing.
Usual causes
- Warped cookware
- A partly broken radiant element
- A dual-element section that has stopped working
- Gas burner ports that are partly blocked
What we do
We begin by laying your pans on a flat surface to check for warping, then test every section of the heating element or burner. Whatever is found, a broken radiant element, a faulty dual-element switch or a partly obstructed burner, is put right, and a pan of water is heated to confirm that the zone now heats evenly.
Element will not switch offAn element keeps glowing or stays hot after its control has been turned off. This is a safety hazard. Switch off the cooktop at the circuit breaker and leave it unused until it has been repaired.
Usual causes
- Infinite switch contacts welded together
- A stuck relay on the control board
- A short in the wiring
- Moisture shorting a touch control
What we do
We isolate the power supply and locate the switch or relay that is stuck in the closed position, then replace it. The wiring is examined for heat damage, and before power is restored each element is cycled on and off to confirm that it shuts down completely.
Infinite switch faultyThe knob turns but the element does not respond, or it heats only at certain settings. The infinite switch regulates how much power reaches the element, so a fault here affects control rather than the element itself.
Usual causes
- Burnt switch contacts
- A broken switch shaft
- A loose wire at the switch
- A terminal burnt by a poor connection
What we do
Our technician tests the switch at each position and inspects the attached wiring for scorched terminals. If the switch is defective it is renewed, any scorched wire ends are cut back and reterminated, and we confirm correct operation at low, medium and high.
Element heats only on highThe element produces heat only at the highest setting, or it runs at full power regardless of where the control is set. Either way, the switch responsible for regulating it has failed.
Usual causes
- A stuck infinite switch
- Welded switch contacts
- A control fault on electronic models
- An incorrect replacement switch fitted previously
What we do
At lower settings an infinite switch should pulse power to the element, and our technician confirms whether that pulsing is taking place. A failed or incorrect switch is replaced with the part specified for your model, and the element is verified at every setting.
No spark at the igniterA single burner has stopped clicking, or none of them click at all. The usual explanations are a cracked igniter or a spark module that no longer produces voltage.
Usual causes
- Cracked igniter porcelain
- A failed spark module
- A loose igniter wire
- An igniter tip set too far from the burner
What we do
Our technician checks for spark at every igniter and measures the output of the module. A cracked igniter or failed module is replaced, and the spark gap is set so that each burner lights within a few clicks.
Gas valve stiff or leakingA knob becomes hard to turn, or turning it no longer changes the flame. A valve that leaks may also produce a smell of gas. Burner valves wear gradually over many years of use.
Usual causes
- A seized valve stem
- A worn valve seat
- Dried-out lubricant inside the valve
- A leak around the valve stem
What we do
We check the valve with a gas detector and assess how smoothly it rotates. A valve that is worn, stiff or leaking is replaced, and the full cooktop is leak tested before we leave.
Show 14 further cooktop faults
Control knob broken or slippingThe knob turns freely without moving the valve or switch, or the knob itself is cracked. Without a secure knob, it becomes difficult to set the heat safely.
Usual causes
- A worn knob insert
- A cracked knob
- A damaged valve or switch shaft
- A knob deformed by heat
What we do
Our technician fits a new knob and inspects the shaft beneath it. Where that shaft has been stripped, the valve or switch behind it is renewed, giving the knob a firm grip and accurate heat control.
Hot-surface light faultyThe hot-surface indicator remains lit long after the glass has cooled, or it never lights at all. Its purpose is to warn you while the surface is still hot enough to cause a burn, so it should be working correctly.
Usual causes
- A failed lamp or LED
- A stuck limiter switch
- A control board fault
- Loose wiring
What we do
We test the indicator, the limiter on the element and the output from the control. The faulty component is replaced so the warning lights while the glass is hot and switches off once it has cooled.
Induction zone not sensing panA zone stays cold while its display blinks or presents a cookware symbol. Induction requires magnetic cookware; if a magnet will not hold to the base of the pan, the zone cannot use it.
Usual causes
- Non-magnetic cookware such as aluminum or copper
- A pan too small for the zone's sensor
- A failed pan detection circuit
- A warped pan base
What we do
Our technician tests the zone with a pan known to work on induction and runs the diagnostic routine. Once cookware has been ruled out, the defective pan sensor or board is renewed, and the zone is proven with more than one pan.
Error code on induction cooktopThe display shows a code, for example E1, E7 or the letter F with a number. Such codes generally indicate overheating, a sensor fault or a problem with one of the circuit boards.
Usual causes
- Overheating
- A sensor fault
- A power board fault
- A communication fault between boards
What we do
Our technician interprets the code using the service documentation for your model, then tests whichever circuit it identifies, such as a sensor, the cooling fan or the power board. After the defective part is renewed and the fault memory reset, we run the cooktop up to full output to confirm the repair.
Loud buzzing from induction cooktopInduction cooking naturally produces some hum, particularly at high power or with certain types of pan. A buzz that is loud or has appeared recently may come from the cooling fan or a component that has worked loose.
Usual causes
- A lightweight or multi-layer pan
- A worn cooling fan
- A loose coil
- A pan that does not sit flat
What we do
Our technician first tests with a heavy, flat-bottomed pan to rule out the cookware, then examines the cooling fan and the coil mountings. A noisy fan or loose coil is corrected, and we explain which kinds of pan are more likely to hum on induction.
Cooktop completely without powerNo zone or display works at all. The circuit breaker is the first thing to check. Electric and induction cooktops run on a 240-volt circuit, and if only one half of a double breaker trips the cooktop can appear completely dead.
Usual causes
- A tripped breaker
- A burnt terminal block
- A blown fuse on the control board
- A failed control board
What we do
At the terminal block, our technician confirms that each half of the 240-volt supply is present and inspects the connections for scorching. Once the defective block, fuse or board has been renewed, every zone is switched on to confirm it works.
Scratched or stained glass topMost scratches and marks on a glass top are cosmetic. Deep scratches, however, can weaken the glass. They are usually caused by cookware with rough bases or by abrasive cleaners.
Usual causes
- Cast-iron or rough-based pans dragged across the glass
- Abrasive cleaning products
- Burnt-on sugar
- Grit trapped under a pan
What we do
Our technician checks the glass for cracks and removes stains using a cleaner and scraper made for glass tops. If any scratches are deep enough to compromise the glass, we provide a price for a replacement top.
Control lock will not releaseThe lock symbol is displayed and the controls do not respond. On most models, pressing and holding the lock key for several seconds releases it. If that has no effect, the control itself may be faulty.
Usual causes
- The lock feature switched on
- A touch panel fault
- A control board fault
- Water on the lock key
What we do
Our technician clears the lock with the key sequence your model uses and then tests how the touch control responds. Should the panel or board prove defective, it is renewed and each control is operated in turn.
Uneven or lifting burner flameThe flame rises higher on one side, or does not light around the entire burner. This usually means the burner cap is not sitting flat, which is common after the cooktop has been cleaned.
Usual causes
- A cap that is not seated flat
- A cap swapped from a different burner
- A warped burner head
- Food lodged beneath the cap
What we do
Each cap is cleaned and returned to its matching burner, and the heads are checked for level seating. Any warped cap or head is renewed. We then light every burner and look for a flame that is uniform all the way around.
Flames wrong after propane conversionFlames are oversized, yellow and sooty, or very small. These symptoms suggest the cooktop was not fully converted between natural gas and propane. For safety, an incomplete conversion must be corrected before the cooktop is used.
Usual causes
- Incorrect orifices
- A regulator that was not converted
- Simmer screws left unadjusted
- The oven left unconverted while the cooktop was changed
What we do
Our technician checks the orifices, the regulator and the simmer adjustments against the gas your home uses, finishing any steps that were missed. Flames are then set burner by burner, and every joint is checked for leaks before you cook on it again.
Burnt coil element socketThe element sparks, heats intermittently or sits in a socket that has turned black. A burnt socket will also damage any new element plugged into it, so the two are best assessed together.
Usual causes
- A loose element connection
- Corroded socket terminals
- An element left loose in its socket
- Spills reaching the socket
What we do
Our technician replaces the burnt socket, together with the element if its terminals are pitted, because a damaged element will quickly ruin a new socket. The wiring is inspected for heat damage and repaired where necessary.
Induction cooling fan failedAn induction cooktop relies on a fan to keep its electronics within a safe temperature. When that fan stops, the cooktop overheats and shuts itself down for protection.
Usual causes
- A failed fan motor
- Debris blocking the fan
- A blocked vent below the cooktop
- Loose fan wiring
What we do
We test the fan and follow the airflow path beneath the cooktop, including any vent in the cabinet. If the fan has failed it is renewed, and we run the cooktop at high power to verify that the electronics stay within temperature.
Downdraft vent not workingThe downdraft vent fails to rise, or its fan will not run, so smoke and steam remain in the kitchen instead of being drawn away.
Usual causes
- A failed lift motor
- A failed fan motor
- A faulty switch
- A filter clogged with grease
What we do
Our technician tests the lift motor, fan motor and switch, and cleans or replaces the filter. The failed part is replaced, and the vent is checked for correct lift and airflow.
Induction zone shuts off earlyA zone heats normally and then switches off after only a few minutes. Either the overheating protection or a timer is ending the cooking cycle.
Usual causes
- Overheating caused by a blocked vent
- A weak cooling fan
- A faulty temperature sensor
- An automatic shut-off timer
What we do
Our technician inspects the vents, the cooling fan and the temperature sensors, and checks whether an automatic timer was set. The source of the overheating is corrected, and the zone is tested through a longer period of cooking.
Brands
Cooktop manufacturers we service
Technical notes
Cooktops in Houston kitchens
Gas cooktops are common in Houston homes, and remodels have brought plenty of induction units into kitchens that were all-electric. The fuel decides the faults. Gas burners mostly fail at the igniter, spark module and burner ports; radiant glass tops at the element, the infinite switch or a cracked surface; induction units at the power board, a coil sensor or the cooling fan.
Island cooktops with downdraft vents add another set of parts, and built-in pro-style units need careful removal from the counter. We plan for both when you give us the model number at booking.
Moisture and clicking igniters
A spark igniter that keeps clicking after the burner is lit, or clicks on its own, usually has moisture or spilled liquid in a burner switch or the spark module. After a boilover or on a very humid day it may dry out within a few hours. If it does not, the switch or module needs attention; do not keep cooking with liquid in the controls.
Induction boards, heat and power quality
Induction boards are sensitive to heat and voltage swings. Blocked cooling vents beneath a built-in unit, a drawer packed tight under the cooktop, or a surge after a storm can cause zones that cut out after a few minutes or error codes at power-up. Note the exact code and the model number before you call; it often tells us which board or sensor to bring.
Safe cooktop checks, and when to stop
On gas burners, seat each cap and burner head squarely and let a wet burner dry fully before trying again. On induction, test the pan with a magnet and make sure the cooling vents under the cooktop are not blocked by a packed drawer. If you smell gas, turn the burner off, do not operate switches, leave the house and call the gas utility or 911 from outside. A cracked glass top should not be used at all; switch it off at the breaker.
Igniters, spark modules, burner switches, infinite switches and radiant elements are the common repairs. Induction power boards and coil assemblies cost considerably more, and on some models a replacement glass top approaches the price of a new cooktop.
Questions
Cooktop questions we hear often
Why is the flame on my gas cooktop yellow or lazy?
A misaligned burner cap, food or cleaner blocking the ports, or a burner set up for the wrong gas are the common causes. A flame that stays yellow and leaves soot on pans should be looked at promptly, because it means incomplete combustion. If you smell gas, turn the burner off, leave the house and call your gas utility first.
Why does one radiant element only work on high?
That almost always means a failed infinite switch, the control behind the knob that cycles the element on and off to give lower settings. When it fails closed, the element runs at full power whatever the knob says. It is a straightforward replacement once the model is known.
My induction cooktop doesn't recognize my pan. Is it broken?
Check the pan first: a magnet should stick firmly to its base, and it should cover most of the marked zone. If a pan that works on other zones is ignored by one zone, the coil, its sensor or the power board for that zone is the likely fault.
Do you repair downdraft vents built into cooktops?
Yes. Pop-up and flush downdraft systems have a blower motor, filters and, on rising models, a lift motor and switches. A vent that will not rise, rises and stops, or runs weakly is usually one of those parts or a filter clogged with grease.
Service area
Cooktop repair across Greater Houston
- Downtown & Midtown
- Montrose
- River Oaks & Upper Kirby
- The Heights
- West University Place
- Bellaire
- Meyerland & Braeswood
- Galleria & Uptown
- Memorial
- Spring Branch
- Energy Corridor
- Clear Lake
- Katy
- Cypress
- Spring
- Humble & Atascocita
- Pasadena
- East End & Fifth Ward
- Northeast Houston & Northshore
- North Houston & Aldine
- Champions & FM 1960
- Cy-Fair & Jersey Village
- Westchase & Sharpstown
- Alief & Southwest Houston
- Medical Center & South Main
- South Park & Sunnyside
- Hobby & Southeast Houston
- Deer Park & La Porte
- Kingwood & Porter
- Tomball
- Sugar Land
- Missouri City
- Richmond & Rosenberg
- Pearland
- Alvin & Angleton
- The Woodlands
- Magnolia & Pinehurst
- Conroe
- League City & Friendswood
- Texas City & La Marque
- Galveston
- Waller & Brookshire
Book a cooktop repair
Tell us gas, radiant or induction, the model number and any error code on the display. We'll set a three-hour window and bring the likely part.