Jump to main content

Appliance repair across Greater Houston

Freezer repair in Houston, for garage, chest and upright freezers.

In many Houston homes the second freezer lives in the garage, which is exactly where summer heat and storm outages hit it hardest.
  • Fault found before any price
  • One fixed price you approve
  • 90-day parts warranty

Free to request · 3 steps

Request a repair appointment

Takes about a minute. There is no charge to submit a request.

Prefer to call?(832) 476-8009
Step 1 of 3: Appliance and fault

Appliance and fault

01Which appliance needs attention?
02What is it doing?
Diagnosis
The cause is identified before any price is given
Approval
One fixed price, and work begins only with your consent
Hours
Our phones are answered 24 hours a day
Warranty
Parts warranted for 90 days, labor for 30
1–2 hours
Usual duration of a visit
30
Freezer faults documented
27
Manufacturers serviced
24/7
Phones answered

Freezer problems

Freezer faults and what they mean

Open the symptom your freezer has. Each card lists likely causes, from a tripped outlet to a failed start relay.

  • Freezer not freezingIce cubes feel wet, food yields to the touch and a thermometer shows a reading well above 0°F. A silent cabinet suggests the compressor is failing to start. A cabinet that runs without pause suggests the system is operating but cannot remove heat fast enough.

    Usual causes

    • Start relay or overload preventing compressor start
    • Blocked condenser coil or fan trapping heat
    • Upright's evaporator fan no longer turning
    • Failed defrost leaving the coil encased in ice
    • Sealed-system refrigerant leak

    What we do

    Our technician begins by confirming whether the compressor runs and how much heat the condenser is giving off. Those two observations separate a starting fault from a heat-rejection, airflow or sealed-system problem. The relay, fans, defrost components or system pressures are then tested as indicated, and we replace only the part shown to have failed.

  • Frost accumulating in an uprightA frost-free upright should remain largely clear inside. When a white layer forms on the rear wall or shelves and grows thicker week by week, either the defrost cycle has stopped working or moist room air is entering. Left alone, the frost will eventually block the airflow.

    Usual causes

    • Burnt-out defrost heater
    • Defrost thermostat stuck open
    • Timer or control board not starting defrost
    • Worn door gasket admitting humid air
    • Frequent door opening in summer

    What we do

    With the rear panel removed, the pattern of frost on the coil shows whether the defrost system or a door leak is responsible. Each of these parts, from the heater and thermostat to the timer or board, is checked for continuity and correct output. After the faulty component is replaced, a forced defrost is run so we can watch the coil clear completely.

  • Unusual freezer noisesClicks, a steady hum and occasional crackling are ordinary sounds of a freezer at work. A rattle, squeal or harsh buzz that was not there before deserves attention. Units in garages often stand on sloped or uneven concrete, which amplifies any vibration.

    Usual causes

    • Ice in the path of the evaporator fan
    • Worn condenser fan motor bearings
    • Compressor rattling on tired mounts
    • Cabinet out of level, tubing touching metal

    What we do

    We remove the access panels and listen to locate the source precisely, turning each fan by hand to feel for resistance. A worn motor is replaced, any tubing in contact with the cabinet is carefully eased away, and the freezer is leveled on its feet or casters.

  • Water leaking from the freezerWater on the floor near a freezer is nearly always melted frost that has not gone where it should. An upright directs defrost water to a pan beneath the cabinet. A chest freezer has a drain plug near the base, and it is sometimes left open after a manual defrost.

    Usual causes

    • Clogged or frozen defrost drain tube
    • Cracked or displaced drain pan
    • Chest freezer drain plug left open
    • Gasket leak producing heavy, melting frost

    What we do

    Our technician traces the water to its origin and flushes the drain using warm water. Where the pan is cracked or a drain heater has failed, it is replaced; on chest models the plug and outer cap are inspected and seated correctly.

  • Door or lid seal leakingSigns of a poor seal include frost along the door edge, a compressor that rarely rests and a lid that closes without a firm feel. A simple test is to shut the door on a dollar bill; you should feel resistance when you pull it out. A worn gasket allows warm, moist air into the cabinet.

    Usual causes

    • Torn or compressed gasket
    • Gasket stiffened by age
    • Sagging hinge on an upright
    • Weak lid hinge spring on a chest model

    What we do

    We examine the entire perimeter of the gasket and check the hinges for sag or loss of spring tension. Realigning the door or lid comes first; if the seal still leaks afterwards, a gasket matched to the model is fitted and gently warmed so it seats evenly.

  • Freezer running too coldFood is frozen rock-solid, the door resists opening and the compressor appears never to rest. A freezer is normally kept near 0°F. Temperatures far below that consume extra electricity and often indicate a control that is no longer switching the compressor off.

    Usual causes

    • Temperature control contacts stuck closed
    • Thermostat sensing bulb dislodged
    • Fast-freeze mode left switched on
    • Electronic sensor reporting falsely warm

    What we do

    We measure the true cabinet temperature and confirm whether the control stops the compressor at its set point. A thermostat that will not open or a sensor reading out of range is replaced, and any quick-freeze setting is returned to normal.

  • Freezer only partly coldInstead of holding 0°F, the cabinet settles somewhere between 10 and 20°F, so ice cream turns soft while meat stays frozen. A gradual decline of this kind usually points to restricted airflow or poor heat rejection rather than a sudden failure.

    Usual causes

    • Dust-covered condenser coils
    • Condenser fan turning slowly
    • Large load of warm food added
    • Refrigerant charge running low

    What we do

    Our technician cleans and tests the condenser side first, then checks evaporator temperatures and the compressor's current draw. If those readings are sound, system pressures are measured to establish whether a leak is present.

  • Freezer runs without stoppingSome additional running time during a heatwave is expected. A compressor that never cycles off in a cool room is different, and it means heat is either entering the cabinet or not being carried away from it.

    Usual causes

    • Leaking door or lid seal
    • Dust-coated condenser coils
    • Unit installed in a very hot garage
    • Thermostat stuck in the on position
    • Low refrigerant charge

    What we do

    We time the running cycle and note the room temperature, then work through the seals, the coils and the thermostat in order. The cause is corrected and we confirm the compressor now switches off as designed.

  • Temperature alarm keeps beepingMany models sound an alert when the door is left ajar or the cabinet temperature climbs. A brief alarm after a power cut is expected while the freezer recovers. An alarm that persists means the cabinet really is warming, or the sensing circuit is at fault.

    Usual causes

    • Door not closed completely
    • Cabinet warming from a cooling fault
    • Faulty temperature sensor
    • Recent load of warm food

    What we do

    We check the door closure and verify the actual temperature with our own calibrated thermometer. A genuinely warm cabinet leads us to diagnose the cooling fault; a normal reading leads us to test and, if needed, replace the sensor or alarm board.

  • Freezer completely deadThe light is off, the compressor is silent and the cabinet is warming. Garage freezers are frequently on GFCI outlets, which can trip quietly and stay off. Before anything else, test that outlet with a lamp or similar small appliance.

    Usual causes

    • Tripped GFCI outlet
    • Tripped circuit breaker
    • Damaged power cord
    • Failed thermostat or control

    What we do

    Our technician confirms voltage at the outlet and inside the unit, then follows the circuit through the cord, the thermostat and the compressor wiring. Once the break is repaired, we leave the freezer running and pulling down in temperature.

  • Chest freezer stopped coolingA chest freezer is a simple machine: a compressor, a thermostat and refrigerant coils embedded in the cabinet walls, usually with no fan at all. When it stops cooling, the fault usually lies with the start components, the thermostat or the sealed system.

    Usual causes

    • Failed start relay
    • Thermostat failed open
    • Compressor overheating from blocked ventilation
    • Refrigerant leak in the wall coils

    What we do

    We test the thermostat and start relay and take resistance readings on the compressor windings. Where refrigerant has escaped, we explain your options plainly, because a leak in coils sealed inside foam walls is frequently uneconomical to repair.

  • Garage freezer struggling in extreme weatherEach freezer is engineered to work within a set band of surrounding temperatures. A Houston garage in July and August can sit above the top of that band for weeks, so the condenser cannot shed heat fast enough and the compressor runs almost without stopping. On the rare nights of a hard freeze, the opposite can happen: a thermostat sensing cold surroundings stops calling for cooling. Models sold as garage-ready tolerate these conditions better.

    Usual causes

    • Summer garage heat beyond what the condenser can shed
    • Dust-packed condenser coils or a slow condenser fan
    • GFCI tripping in humid conditions
    • Model not rated for garage use
    • A hard freeze keeping the thermostat idle

    What we do

    We compare the temperature we record in the garage with the ambient range the manufacturer specifies for the model. Where the manufacturer offers one, a low-ambient heater kit can be installed, or the unit can be relocated; if neither is practical, we give you a straightforward account of the alternatives.

  • Automatic defrost not workingIn a frost-free upright, a heater melts frost from the evaporator coil several times each day. If that cycle stops, ice accumulates on the coil until air can no longer pass through, and the cabinet warms gradually over a period of days.

    Usual causes

    • Open defrost heater
    • Failed defrost thermostat
    • Timer or board not initiating defrost
    • Broken wiring near the heater

    What we do

    Our technician tests each part of the defrost circuit and confirms that the control actually begins a defrost. The failed component is replaced and a forced defrost clears the coil before we leave.

  • Condenser coils clogged with dustThe condenser is where the freezer releases the heat it removes from the cabinet. A blanket of dust slows that process, lengthening run times and raising compressor temperature. Uprights generally have the coil at the back or underneath, while many chest models hide it within the walls.

    Usual causes

    • Accumulated dust and lint
    • Cabinet pushed tight to the wall
    • Pet hair pulled in by the fan

    What we do

    We clean the coil with a coil brush and vacuum, then confirm the fan and airflow are unobstructed. Afterwards the compressor's running temperature is checked to make sure the period of overheating caused no lasting harm.

  • Compressor not runningThe compressor circulates refrigerant through the system, so if it fails to start, hums without running or keeps clicking off, no cooling takes place. In practice the small start components fail far more often than the compressor itself.

    Usual causes

    • Failed start relay
    • Overload protector tripping
    • Burnt compressor windings
    • Mechanically seized compressor

    What we do

    We measure winding resistance, test the start components and record the current drawn on start-up. If the compressor is confirmed as the failed part, we set out honestly whether a sealed-system repair is sensible or whether replacing the freezer is the better use of your money.

  • Evaporator fan stoppedIn a frost-free upright, a fan concealed behind the rear panel moves cold air from the coil into the storage area. When it stops, the coil remains cold but the food compartment slowly warms. A squeal from the back of the cabinet often comes before the failure.

    Usual causes

    • Worn fan motor
    • Ice obstructing the blade
    • Faulty door switch

    What we do

    With the panel removed, we test the motor and the door switch that controls it. A failed motor is replaced, and where ice was the cause, the defrost fault that produced it is repaired at the same visit.

Show 14 further freezer faults
  • Condenser fan not turningMany uprights have a small fan beside the compressor that draws air across the condenser. Without it, the compressor overheats and its overload switches it off repeatedly, and cooling performance falls away quickly.

    Usual causes

    • Seized fan motor
    • Blade jammed by debris
    • Wiring fault

    What we do

    We confirm the fan receives voltage whenever the compressor runs and that the blade spins freely. A seized motor is replaced and the compressor compartment is cleared of debris.

  • Clicking, but no coolingA click from the compressor area every few minutes, with the cabinet failing to cool, is the sound of the compressor attempting to start and giving up. The start relay is the most common culprit.

    Usual causes

    • Cracked start relay
    • Worn overload protector
    • Low voltage at the outlet

    What we do

    Our technician tests the relay and overload and measures outlet voltage while the compressor tries to start. A correctly matched relay and overload are installed, and running current is checked afterwards.

  • Refrigerant leak suspectedCooling weakens gradually over several weeks, the compressor may run without pause and part of the evaporator coil stays warm to the touch. Refrigerant work requires EPA-certified handling and specialized recovery equipment.

    Usual causes

    • Corrosion on the coil
    • Damaged refrigerant tubing
    • Coil pierced while chipping ice
    • Leaking brazed joint

    What we do

    We measure the system pressures and locate the leak with an electronic detector. Any repair is carried out under EPA Section 608 rules, and we tell you candidly whether the work is justified for your particular freezer.

  • Temperature swinging up and downReadings vary widely from one day to the next, and food may partly thaw before freezing again, which degrades its texture and flavor. The cause is usually a sensor, the thermostat or the defrost cycle.

    Usual causes

    • Thermostat calibration drifting
    • Sensor dislodged from its clip
    • Defrost cycle running too long
    • Door opened frequently

    What we do

    We place a thermometer of our own in the cabinet and record temperatures across several compressor cycles, then compare the thermostat or electronic sensor with its specification. We replace a control that has drifted, refit a sensor that has come loose, and the defrost duration is verified.

  • Heavy ice on chest freezer wallsMost chest freezers are manual-defrost, so a layer of ice forms on the walls over time. Once it exceeds roughly a quarter of an inch, it reduces both efficiency and usable space. Ice that thickens quickly may also mean the lid is not sealing properly.

    Usual causes

    • Long interval since the last defrost
    • Leaking lid gasket
    • Lid opened often in humid weather

    What we do

    We defrost the cabinet carefully without sharp implements, which can puncture the refrigerant coils in the walls, and examine the lid seal. Fitting a new gasket where the old one leaks means ice forms far more slowly from then on.

  • Defrost drain blockedIn an upright, meltwater from each defrost runs through a tube to a pan below. If the tube blocks, the water collects inside the cabinet and freezes into a sheet on the bottom.

    Usual causes

    • Debris over the drain opening
    • Drain frozen from a failed heater or heat clip
    • Kinked drain hose
    • Cabinet tilting forward, away from the drain

    What we do

    Our technician thaws the drain and flushes it with warm water until it flows freely into the pan. If the copper heat clip or drain heater has failed, it is renewed, and the cabinet is leveled so meltwater reaches the drain.

  • Door sticks shut after closingWhen the door closes, the warm air that entered cools and contracts, creating a slight vacuum that holds the door for a minute or so. That is expected behavior. If the door remains difficult to open well after that, the gasket may be adhering to the cabinet.

    Usual causes

    • Ordinary vacuum after closing
    • Gasket sticky from dried spills
    • Blocked pressure-relief vent
    • Failing gasket heater on some models

    What we do

    We clean the gasket and, where the model has one, check that the pressure-relief vent is clear. A torn or tacky gasket is replaced. We also explain that a brief resistance just after closing is normal and not a sign of a fault.

  • Interior light not workingThe cabinet stays dark when the door opens. In most cases the bulb has simply failed, although models with LED lighting may need a replacement LED board.

    Usual causes

    • Burnt-out bulb
    • Failed LED board
    • Faulty door switch
    • Loose wiring at the light housing

    What we do

    Our technician checks the lamp or LED board, the switch in the door frame and the supply wiring, then replaces the component at fault. We also confirm the light turns off when the door shuts, since a lamp left on adds heat to the cabinet.

  • Unpleasant odor in the freezerAn odor usually indicates that food thawed and refroze at some point, often during a power outage. Liquid from spoiled food can also find its way into the drain or the insulation.

    Usual causes

    • Food spoiled during a warm period
    • Stale water in the drain pan
    • Liquid absorbed into insulation
    • Spills beneath shelves or in the drain

    What we do

    Our technician cleans the interior, the drain line and the pan with a food-safe solution and checks whether liquid has penetrated the insulation. If a warm period caused the spoilage, we identify the cooling fault responsible so it does not recur.

  • Freezer tripping the GFCIThe protective outlet trips and the freezer loses power, often without anyone noticing for some time. This is common in humid garages and on covered patios, and in some cases the freezer itself has a small leakage of current to ground.

    Usual causes

    • Moisture inside the outlet
    • Defrost heater leaking current to ground
    • Worn insulation on compressor wiring
    • Damaged older power cord

    What we do

    We test the heater, the compressor and the wiring for leakage to ground using an insulation tester, and replace any heater or wire that fails. Should the freezer pass every test, we discuss what can be done at the outlet and recommend consulting a licensed electrician.

  • Not cooling after a power outageOnce power returns, the freezer either fails to restart or cools only slowly. Some electronic controls require a reset, and a surge on restoration can damage relays and control boards.

    Usual causes

    • Control awaiting a reset
    • Surge damage to the control board
    • Tripped compressor overload
    • Start relay damaged by the surge

    What we do

    We check that the control has reset correctly, then test the board, the start relay and the compressor circuit. Any part harmed by the outage is renewed, and we stay until the compressor has completed several normal cycles.

  • Compressor short-cyclingThe compressor switches on and off every few minutes. Repeated short starts place considerable strain on it, and the overload protector or the thermostat is usually what is cutting it off.

    Usual causes

    • Overload tripping from heat
    • Thermostat bulb out of position
    • Failed condenser fan
    • Low refrigerant charge

    What we do

    Our technician times the on and off periods and checks the overload, the position of the thermostat bulb and the condenser fan. Once the bulb is repositioned or the faulty part renewed, we confirm the compressor returns to cycles of normal length.

  • Food developing freezer burn quicklyFreezer burn appears as dry, grayish patches on the surface of food. A little is expected on items stored for many months, but rapid freezer burn suggests unstable temperatures or air entering the cabinet.

    Usual causes

    • Temperature swings from a drifting control
    • Leaking door or lid gasket
    • Loosely wrapped food
    • Overly frequent defrost cycles

    What we do

    Our technician records how steady the temperature remains across several cycles and checks the door or lid seal. A drifting control or leaking gasket is corrected, and we offer some practical storage advice to help food retain its quality.

  • Built-in ice maker not producingSome upright freezers have an ice maker built in. When it stops producing, first confirm that the water supply is connected and turned on, and that the ice maker itself is switched on.

    Usual causes

    • Frozen water line
    • Failed inlet valve
    • Failed ice maker module
    • Cabinet too warm for a harvest cycle

    What we do

    We verify the water supply and cabinet temperature, then check the inlet valve and trigger a diagnostic harvest cycle. Whether the fault is a frozen line, the valve or the module, it is corrected, and we observe the following harvest to confirm normal operation.

Brands

Freezer manufacturers we service

All brands →
  • Samsung
  • LG
  • Whirlpool
  • GE Appliances
  • Maytag
  • Bosch
  • KitchenAid
  • Frigidaire
  • Sub-Zero
  • Viking
  • Kenmore
  • Amana
  • Electrolux
  • Miele
  • Thermador
  • Admiral
  • Atosa
  • Avanti
  • Blomberg
  • Everest
  • Fisher & Paykel
  • Hoshizaki
  • Hotpoint
  • Insignia
  • Roper
  • True Residential
  • Turbo Air

Technical notes

Freezers in Houston garages and utility rooms

Stand-alone freezers in Houston are mostly garage freezers, and garages here hold the summer heat well into the night. A freezer working in that space runs its compressor much longer, packs dust into its condenser faster and has less margin when a fan or start relay begins to fail. Upright models add an automatic defrost system and fans to that list; chest freezers have fewer parts but depend on a good lid seal.

We test the start relay, overload and compressor circuit, the fans, the defrost heater and thermostat on uprights, and the gasket, then compare what the freezer is doing with the ambient range the manufacturer specifies. If the garage itself is the problem, we say so rather than sell you a part.

Restarting after hurricane-season outages

When power returns after a storm, start-up surges and brownouts are hard on start relays and electronic controls. If a freezer hums, clicks every few minutes and does not get cold after an outage, unplug it and call; repeated start attempts on a weak relay can overheat the compressor. A dedicated surge protector rated for appliances is a sensible addition in the garage.

GFCI outlets in humid garages

Garage outlets are typically GFCI-protected, and a freezer can trip one through moisture in the outlet, a defrost heater leaking current, or damaged wiring. Humid garages make it more likely. A tripped GFCI makes no noise, so a garage freezer is worth checking daily during a stretch of storms.

Checks before a freezer visit, and what decides the price

Look first for a tripped GFCI outlet in the garage, a lid or door that is not sealing, and dust packed on the condenser coil at the back or base. Listen to it: a compressor that clicks on, hums for a few seconds and clicks off points to the start relay or overload, and repeated attempts can overheat the compressor, so unplug it and call. A thermometer inside tells you how quickly it is warming and whether the food needs to move to another freezer or a cooler with ice.

Start relays, fans, door gaskets and defrost parts on an upright are the usual repairs. A compressor or refrigerant leak is sealed-system work, the costliest repair a freezer can need. Many chest freezers carry their refrigerant tubing inside the cabinet walls, and a leak there is rarely economical to repair.

Questions

Freezer questions we hear often

How long will food stay frozen if my freezer stops?

USDA guidance is about 48 hours for a full freezer and about 24 hours for a half-full one, provided the door or lid stays closed. Food that still has ice crystals or reads 40°F or below can be refrozen. Keep the door shut until the technician arrives.

Why is frost building up on the walls of my chest freezer?

Chest freezers are manual-defrost, so some frost is normal and should be cleared when it builds to around a quarter of an inch. Fast buildup means warm, humid air is getting in: a lid gasket that no longer seals, a lid left ajar, or frequent opening in a muggy garage.

My freezer runs but isn't cold. Is it the compressor?

Often not. A dusty condenser, a stopped condenser fan or a failing start relay can all leave a freezer running warm, and on an upright a failed evaporator fan or defrost fault does the same. We rule those out before testing the compressor and sealed system.

Can a freezer go on a covered patio or in an outdoor kitchen?

Only one rated for outdoor use. A standard freezer outside faces rain, high humidity and heat beyond its rated range, which shortens its life and trips GFCI outlets. Outdoor-rated models are built and sealed for those conditions.

Save what's in your freezer

Tell us chest or upright, where it stands and what the thermometer reads. We'll set a three-hour window and treat a thawing freezer as the priority it is.

Call, any hour(832) 476-8009Book on the web