Jump to main content

Appliance repair across Greater Houston

Oven repair in Houston, for wall ovens, gas ovens and electric.

An oven that runs cool or won't heat usually has a weak igniter, a burnt element or a drifting sensor. We measure before we replace anything.
  • Fault found before any price
  • One fixed price you approve
  • 90-day parts warranty

Free to request · 3 steps

Request a repair appointment

Takes about a minute. There is no charge to submit a request.

Prefer to call?(832) 476-8009
Step 1 of 3: Appliance and fault

Appliance and fault

01Which appliance needs attention?
02What is it doing?
Diagnosis
The cause is identified before any price is given
Approval
One fixed price, and work begins only with your consent
Hours
Our phones are answered 24 hours a day
Warranty
Parts warranted for 90 days, labor for 30
1–2 hours
Usual duration of a visit
30
Oven faults documented
31
Manufacturers serviced
24/7
Phones answered

Oven problems

Oven faults and their usual causes

Pick the symptom your oven shows. Each card covers the likely parts and how we confirm the faulty one.

  • Oven stays coldThe panel shows that preheating is under way, yet the cavity remains cool or only faintly warm. In an electric oven, the lower bake element is the first component we suspect. In a gas oven, look through the slots in the floor panel: if there is no glow at all, or a glow without any flame following it, the ignition circuit is almost certainly responsible.

    Usual causes

    • Lower bake element has an open break
    • Igniter current below what the valve needs
    • Gas safety valve has stopped opening
    • Temperature probe registering an open circuit
    • Relay on the control board not closing

    What we do

    With the oven calling for heat, our technician measures the voltage arriving at the element or igniter. On a gas model, the igniter's amperage is compared with the figure the valve requires before it will open. Whichever component fails its test is replaced, and the oven is brought fully to temperature in your presence.

  • Food bakes unevenlyOne side of a tray of biscuits darkens while the other remains pale, or a cake rises higher at one edge. Every oven has some variation from one area of the cavity to another. Pronounced hot and cool zones, however, usually indicate that an element or burner is producing heat along only part of its length.

    Usual causes

    • An element with a section that no longer heats
    • Convection fan has stopped turning
    • Heat escaping past the door seal
    • Appliance sitting out of level
    • Baking pans set very close to the cavity walls

    What we do

    Our technician places a thermocouple at several positions to map how heat is distributed, and confirms that each element warms evenly from end to end. The convection fan and the door seal are then examined, the appliance is leveled, and a test bake confirms the result.

  • Temperature doesn't match settingDishes need far longer than the recipe states, or they scorch at the correct setting. An oven normally cycles roughly 15–25°F above and below its target, and that swing is expected. A steady difference larger than this is a genuine fault and is worth correcting.

    Usual causes

    • Temperature probe drifting from its rated values
    • Probe resting against the cavity wall
    • Calibration of the control has shifted
    • Heat leaking through a worn door seal

    What we do

    Our technician records the true cavity temperature across several heating cycles and checks the probe's resistance against the manufacturer's figures. A probe that has drifted is replaced; where the model permits it, the control's calibration offset is adjusted instead.

  • Gas odor near the ovenA brief trace of gas in the moment before a burner lights can be normal. A strong odor, or one that lingers, is not. When the odor is strong, avoid touching any light switch or appliance, get everyone out of the home, and only then telephone your gas utility from outdoors.

    Usual causes

    • A fitting at the valve or regulator has loosened
    • Gas flowing while the burner fails to ignite
    • Flexible gas connector damaged
    • Safety valve not shutting off completely

    What we do

    Our technician tests each joint with an electronic leak detector and observes the full ignition sequence. Any leaking fitting or defective valve is replaced, and the appliance is tested again before we leave.

  • Self-clean cycle failsThe cleaning cycle refuses to start, ends early, or leaves residue and ash in the cavity. Because self-clean reaches far higher temperatures than ordinary cooking, it is often the cycle that first reveals a component nearing the end of its life.

    Usual causes

    • Latch motor not engaging the door
    • Probe reading outside its range at high heat
    • Thermal fuse has opened
    • Control board relay failing under heavy load

    What we do

    Our technician runs the latch through its test, then checks the probe and the thermal fuse. The defective part is replaced, and we give you our honest view on whether an older oven should continue to use the self-clean cycle.

  • Door won't unlockFollowing a cleaning cycle or an interruption to the power, the door remains latched. The latch motor or its position switch has usually failed. Pulling hard on the handle can distort the latch mechanism and add to the repair.

    Usual causes

    • Latch motor no longer turns
    • Position switch not reporting to the control
    • Cavity has not yet cooled to unlocking temperature
    • Fault within the control board

    What we do

    Once the cavity has cooled completely, our technician operates the latch from the control's diagnostic mode and observes whether the motor responds. A jammed latch is freed manually from behind the control panel. The motor or switch is then replaced and the latch is checked in both the locking and unlocking directions.

  • Door leaves a gapA visible gap remains along the top or side of the closed door, and heat escapes into the room. Cooking takes longer and the kitchen becomes uncomfortably warm. Worn hinges or a deteriorated seal are the usual explanation.

    Usual causes

    • Weakened springs inside the hinges
    • A hinge arm that has bent
    • Seal hardened or torn
    • Door not fully engaged in its hinge slots

    What we do

    Our technician removes the door, examines each hinge for a broken spring or a bent arm, and inspects the seal. Hinges are always replaced in pairs, a hardened seal is renewed, and the door is reinstalled and checked for gaps with a light inside the cavity.

  • Display blank or flickeringThe display is dark, flickers, or is missing segments of its digits. Depending on the fault, the oven may still heat or may not respond at all. Please check the circuit breaker before anything else.

    Usual causes

    • Power supply section of the control has failed
    • Display board affected by heat
    • Ribbon connector has worked loose
    • Damage from an electrical surge
    • Tripped breaker removing one leg of the supply

    What we do

    Our technician confirms that line voltage reaches the control, checks each low-voltage supply the board produces, and inspects the ribbon to the display. Whichever of the three has failed is renewed; afterwards the clock is set and each cooking mode is tried in turn.

  • Cooktop burner won't heatA single burner or element on the cooktop of your range fails to light or warm, while the others operate normally. On electric ranges, the element or its control switch is often the cause. On gas ranges, the burner cap and its ports should be inspected first.

    Usual causes

    • Infinite switch or burner valve has failed
    • Burner ports blocked by debris
    • Spark electrode or igniter cracked
    • Element receptacle scorched

    What we do

    Our technician checks the heating element or igniter serving that burner, along with the control switch or gas valve that its knob operates. Blocked ports are cleared with a fine pin, a scorched receptacle is replaced together with its element, and a faulty switch or igniter is renewed. The burner is then tested at both high and low settings.

  • Bake element failedIn an electric oven, the lower element supplies most of the baking heat. When it fails, it may show a blister or a visible break, or it may simply remain dark. The broiler often continues to work.

    Usual causes

    • Element sheath worn out after long service
    • Corrosion from spilled food
    • Aluminum foil on the floor causing overheating

    What we do

    Our technician checks the element for continuity and inspects the wiring behind the rear panel. A replacement element is installed, and the oven is heated to confirm it works.

  • Broiler won't heatThe upper element remains dark when broil is selected. Baking can also become slower, because many ovens use the upper element to assist during preheat.

    Usual causes

    • Upper broil element has failed
    • Broil relay on the control has failed
    • Loose connection at the element terminals
    • Corrosion from grease spatter

    What we do

    Our technician tests the element for continuity and measures the voltage at its terminals with broil selected. A failed element is replaced. If the element is sound but receives no power, the broil relay on the control is repaired, and the broiler is run for several minutes to confirm.

  • Gas oven won't igniteYou switch the oven on, wait, and no flame appears. In most current gas ovens, the igniter must draw a specific level of current before the safety valve will release gas. As an igniter ages and that draw falls, the valve stays closed.

    Usual causes

    • Igniter weakened or broken
    • Gas safety valve has failed
    • Shutoff valve on the supply line closed
    • Control not supplying power to the igniter

    What we do

    Our technician measures the igniter's amperage in circuit, checks the voltage at the igniter and confirms that the supply valve is open. Where the igniter has worn, a new one is fitted; where the valve has failed, it is renewed and its joints are leak-tested. Several ignitions in succession then follow to confirm consistent ignition.

  • Temperature probe faultThe temperature probe is a slender rod mounted at the rear of the cavity. When it fails, the oven can overheat, underheat or display a fault code. It is one of the parts we replace most routinely on ovens.

    Usual causes

    • Probe resistance drifting from specification
    • Wiring damaged near the connector
    • Probe bent into contact with the cavity wall
    • Corrosion on the connector behind the oven

    What we do

    Our technician measures the probe's resistance at room temperature, compares it with the specification for your model and checks its wiring harness. A faulty probe is replaced and positioned clear of the wall, and the cavity temperature is verified with an independent thermometer.

  • Control board malfunctionThe oven ignores your settings, produces heat when it should not, or shows fault codes without an obvious cause. Each of these can result from a failed control board. The probe and wiring are always ruled out first.

    Usual causes

    • Relay contacts fused or burnt
    • Heat damage after self-clean cycles
    • Electrical surge
    • Moisture reaching the control area

    What we do

    Only after the probe, keypad and wiring have been cleared does our technician test the board's relays and inputs against the wiring diagram. A board confirmed as faulty is replaced and set up for your model, and before the visit ends we operate every mode the oven offers, convection included, to confirm correct behavior.

  • Door hinge brokenThe door falls open, sits at an angle or will not remain shut. Oven hinges carry considerable weight, and a broken hinge makes the door unsafe while allowing heat to escape.

    Usual causes

    • Hinge spring has broken
    • Hinge arm distorted
    • Worn hinge slots in the oven frame
    • Weight placed on the open door

    What we do

    Our technician removes the door and installs two new hinges so that the tension is balanced on both sides. The frame slots are inspected for wear, the door is reinstalled and adjusted, and we confirm that it closes securely and stays in the broil position.

  • Door glass crackedA pane on the inside or outside of the door has cracked or shattered. Oven doors use tempered glass, and any cracked pane must be replaced. Do not operate the oven if the inner pane is broken.

    Usual causes

    • Sudden cooling, such as cold water on hot glass
    • A pan or rack striking the pane
    • Thermal stress during self-clean
    • Door fasteners tightened excessively

    What we do

    Our technician dismantles the door, removes the broken glass with care and installs the correct tempered pane for the model. The door is reassembled with any spacers or clips that need renewing, then checked for alignment and an even seal.

Show 14 further oven faults
  • Door seal wornThe seal around the door keeps heat inside the cavity. Once it hardens or tears, heat escapes and preheating takes longer. Discoloration on the door frame is a common sign.

    Usual causes

    • Seal hardened over time
    • Seal torn during cleaning
    • Retaining clips broken
    • Seal damaged by self-clean temperatures

    What we do

    Our technician removes the old seal and fits the correct replacement for the model, securing it in every mounting hole. A strip of paper is closed in the door at several points to confirm an even seal, and the preheat time is measured.

  • Convection fan not turningWhen a convection setting is selected, the fan in the rear wall of the cavity should rotate. If it does not, food cooks unevenly and some models display a fault code. A grinding sound often comes before a complete failure.

    Usual causes

    • Fan motor has failed
    • Fan blade loose on its shaft
    • Convection relay on the control has failed
    • Convection heating element failed

    What we do

    Our technician checks whether the blade is loose or seized, measures the motor windings and confirms that the motor receives power with convection selected. Whichever part has failed among these is renewed, after which we cook on a convection setting to verify both rotation and heat.

  • Oven overheatsFood burns at ordinary settings, or the cavity climbs well above the selected temperature. The cause may be a faulty probe or a relay that has stuck closed. A relay that cannot switch off is a safety concern and should be addressed promptly.

    Usual causes

    • Bake relay fused in the closed position
    • Probe reporting a temperature lower than actual
    • Probe incorrectly mounted

    What we do

    Our technician measures the true temperature with an independent thermometer, tests the probe, and watches whether the bake relay releases once the target temperature is reached. A probe that has drifted is replaced; a relay that will not open usually requires a new control board. A complete heating cycle is then run to confirm.

  • F-code on the displayNumbered fault codes, F1, F2, F3 and F7 among them, are used by many manufacturers. These indicate a fault detected in the control, the temperature probe or the keypad. A code tells us where to begin testing, but it does not by itself identify the failed part.

    Usual causes

    • Faulty temperature probe
    • Short circuit in the keypad
    • Overheating condition detected
    • Fault within the control board

    What we do

    Our technician identifies what the code means for your particular model and tests the circuit it refers to, beginning with the probe and keypad. Once the responsible part is renewed we clear the memory and operate the oven for an extended period, watching for any recurrence.

  • Interior light outThe lamp inside the cavity does not come on. The bulb is usually responsible, although the socket or door switch can also be at fault.

    Usual causes

    • Bulb has failed
    • Corrosion in the socket
    • Door switch defective
    • Light relay on the control has failed

    What we do

    Our technician fits an appliance-rated bulb and tests the socket, the door switch and the light output from the control. Any worn socket or faulty switch is renewed, and the lamp is confirmed to work from both the door and the panel button.

  • Smoke from the ovenSmoke during preheating is usually residue from old spills burning away. Smoke from the rear, from behind the controls or from wiring is a more serious matter. If you notice an electrical burning smell, switch the oven off and do not use it.

    Usual causes

    • Food residue on the cavity floor
    • Grease on the broil element
    • Overheating wiring
    • Element short circuit

    What we do

    Our technician establishes where the smoke originates, since cavity smoke, vent smoke and smoke behind the panel each have different causes. Wiring is inspected for scorching, elements for shorts, and the broiler for built-up grease. Damaged components are replaced; if the cause is only old residue, we explain how to clean it safely.

  • Igniter clicks constantlyThe spark igniter continues clicking after the burner lights, or clicks with every knob turned off. Moisture or a stuck spark switch is the most common explanation.

    Usual causes

    • Liquid reaching a spark switch
    • Spark switch stuck closed
    • Burner cap not seated correctly
    • Spark module defective

    What we do

    Our technician dries the area around the knobs, reseats each burner cap, then disconnects the spark switches one by one to identify the shorted switch. The faulty switch or module is replaced, and we confirm the clicking stops with every knob off.

  • Slow to preheatA typical oven reaches 350°F in roughly 10–15 minutes. If yours takes considerably longer, a heat source or the door seal may be weakening.

    Usual causes

    • Gas igniter losing strength
    • Failed broil element lengthening preheat
    • Heat escaping past the door seal
    • Temperature probe drifting

    What we do

    Our technician times the preheat against the manufacturer's specification and tests every heat source, including the upper element that many ovens use while preheating. Igniter current, element continuity and the seal are checked, the weak part is replaced, and a second timed preheat confirms the improvement.

  • Oven trips the breakerThe breaker trips as soon as the oven is switched on, or partway through cooking. A common cause is an element that has shorted to the metal body of the oven.

    Usual causes

    • Element shorted to the oven chassis
    • Damaged wiring
    • Scorched terminal block
    • Moisture inside an element

    What we do

    Our technician disconnects each element and wire and tests it for a short to ground, then inspects the terminal block for scorching. Any shorted component is renewed along with wiring that shows heat damage, and we then measure the amperage while the oven operates.

  • Warming drawer stays coldThe drawer beneath the oven does not warm. Some drawers have a dedicated element, while others rely on residual heat from the oven above.

    Usual causes

    • Drawer element has failed
    • Drawer thermostat defective
    • Drawer switch faulty
    • Loose wiring behind the drawer

    What we do

    Our technician tests the drawer element, thermostat and switch, and checks the wiring at the back of the drawer. The failed component is replaced, and the drawer is run long enough to confirm that it maintains its warm setting.

  • Controls lockedThe display shows 'LOC' or a padlock symbol, and the keypad does not respond. The control lock has often been activated unintentionally, and pressing and holding the designated key for a few seconds usually releases it.

    Usual causes

    • Control lock activated
    • Key stuck in the pressed position
    • Fault in the control board
    • Lock engaged by a self-clean cycle

    What we do

    Our technician releases the lock using the key sequence for your model, then checks whether any key is held down electrically. Should the lock persist, the keypad or the board is replaced and every function is tested.

  • Igniter glows, no flameThe igniter is clearly glowing, yet the gas never lights. Although it glows, it is not drawing enough current to open the safety valve. This is among the most frequent faults on gas ovens.

    Usual causes

    • Igniter has weakened
    • Safety valve not opening
    • Insufficient gas pressure
    • Loose igniter connector

    What we do

    Our technician measures the igniter's amperage in circuit and compares it with the rating of the safety valve. A weakened igniter is renewed; when it tests within range, the valve and gas pressure are examined. The oven is then lit several times to confirm reliable ignition.

  • Meat probe not readingThe oven fails to detect the meat probe, or the temperature it shows is inaccurate. The probe itself or the socket it plugs into may be damaged.

    Usual causes

    • Damaged probe cable
    • Dirty or loose probe socket
    • Fault in the control
    • Probe damaged by a fall

    What we do

    Our technician measures the probe's resistance and cleans and inspects the socket in the cavity wall. A damaged probe or socket is replaced, and the reading is checked against a thermometer in warm water.

  • Element sparkingA bright flash or spark appears at the bake or broil element. This means the element has burned through. Switch the oven off immediately.

    Usual causes

    • Burn-through in the element sheath
    • Corrosion from spilled food
    • Loose terminal connection
    • Aluminum foil in contact with the element

    What we do

    Our technician replaces the element, then examines the terminals and wiring behind the cavity wall for heat damage. Any scorched wire or connector is renewed, and the oven is heated to confirm there is no further sparking.

Brands

Oven manufacturers we service

All brands →
  • Samsung
  • LG
  • Whirlpool
  • GE Appliances
  • Maytag
  • Bosch
  • KitchenAid
  • Frigidaire
  • Viking
  • Kenmore
  • Amana
  • Electrolux
  • Miele
  • Thermador
  • Wolf
  • Admiral
  • AGA
  • Avanti
  • Bertazzoni
  • Blomberg
  • Dacor
  • DCS
  • Fisher & Paykel
  • Gaggenau
  • Hotpoint
  • JennAir
  • La Cornue
  • Roper
  • Smeg
  • Thor Kitchen
  • Vulcan

Technical notes

Ovens in Houston kitchens

Houston kitchens cook on both gas and electricity, and the faults follow the fuel. A gas oven that takes forever to light or shuts off mid-bake usually has a glow-bar igniter that has weakened to the point where the safety valve will not open. An electric oven that will not bake almost always has an open bake element, a failed relay on the control board or a sensor reading the wrong resistance.

Wall ovens are common in newer homes and kitchen remodels, and they are worth repairing for longer because the cabinet opening is cut to fit them. Removing one safely, especially a double wall oven, is part of the job and part of what we plan for when you book.

Self-clean cycles in a hot kitchen

A self-clean cycle drives the cavity far hotter than baking, and that is when tired door locks, thermal fuses and control boards tend to give out. In a Houston summer the air conditioning is already working hard, so an evening self-clean is easier on the kitchen. If the oven stays locked long after it has cooled, do not force the latch; switch the breaker off for a minute and call us if it still will not release.

Outages, surges and touch controls

Many ovens with touch controls lose the clock and settings after an outage, and some show a fault code until reset at the breaker. A surge when power returns after a storm can damage relays on the control board, which tends to show up as a single function failing, such as bake working while broil does not, or a display that stays dark.

Before you call: oven checks and stop signs

Put an oven thermometer on the middle rack before assuming the oven is wrong: a few degrees of drift can often be corrected with the temperature offset in the settings menu. Check that a control lock or Sabbath mode is not on before assuming the controls have failed. Turn the oven off and leave it off if you smell gas, see an element spark or arc, find the inner door glass cracked, or the door stays locked long after a self-clean has cooled.

Igniters, bake and broil elements, temperature sensors and door gaskets are the common, moderate repairs. Gas safety valves, convection motors and door-lock assemblies cost more, and control boards and model-specific door glass sit at the top. On a built-in wall oven, part of the price is taking the oven out of its cabinet without damage and setting it back.

Questions

Oven questions we hear often

Why does my oven take so long to preheat?

On a gas oven, a weakening igniter is the usual cause: it glows, but too slowly to open the valve promptly. On an electric oven, many models use the broil element during preheat, so a failed broil element makes preheat crawl even though baking still works. A worn door gasket letting heat escape is the third common cause.

My gas oven igniter glows orange but the burner never lights. Is that the igniter?

Usually, yes. A glow-bar igniter has to draw enough current to open the oven safety valve, and as it ages it glows without drawing enough. We measure the current rather than judging by the glow, because a failed safety valve shows the same symptom.

Can you replace cracked oven door glass?

Yes. Oven doors have two or more panes, and each is a model-specific part. If the inner pane is cracked, stop using the oven until it is replaced, since it can fail completely under heat. We order the correct glass by model number and rebuild the door at your home.

Do you repair double wall ovens and combination microwave-wall ovens?

Yes. Both are common in remodeled Houston kitchens. A combination unit has a microwave's high-voltage parts above a conventional oven, and either section can fail on its own. Removal from the cabinet is the time-consuming part, and we plan for it when you tell us the model.

Get your oven baking again

Tell us gas or electric, wall oven or range, the model number and what the oven does when you start it. We'll book a three-hour window.

Call, any hour(832) 476-8009Book on the web