Questions clients ask before booking
- Fault found before any price
- One fixed price you approve
- 90-day parts warranty
Phones answered now
- 1You callany hour
- 23-hour windowagreed with you
- 3Fixed pricebefore any work
Free to request · 3 steps
Request a repair appointment
Takes about a minute. There is no charge to submit a request.
- Diagnosis
- The cause is identified before any price is given
- Approval
- One fixed price, and work begins only with your consent
- Hours
- Our phones are answered 24 hours a day
- Warranty
- Parts warranted for 90 days, labor for 30
13 questions · answered here
Can we fix it?
The faults we encounter most often, what typically causes each, and what the repair generally involves.
Can you repair a cooktop burner that will not ignite or heat?
Yes. The sound the burner makes is a useful first clue. A gas burner that clicks but does not light usually has a dirty igniter, blocked burner ports or a weak spark module, while complete silence when you turn the knob suggests a fault in the spark module or in the switch mounted on the knob. On an electric cooktop, a burner that stays cold points to a failed element, a burnt terminal block, or the infinite switch the knob turns. When the required part is already on hand, each of these can be repaired during the same visit. If you smell gas, leave the room without operating switches and contact your gas utility first.
Can you repair a washer that leaks?
Usually, yes. Where the water appears says most about the cause. Under the front of a front-loader it often points to the door boot seal or a drain filter cap that is not fully closed; at the back, to a fill hose or the inlet valve; under a top-loader, to the tub seal or the pump. Our technician runs a fill and drain with the cabinet open to watch the leak happen rather than guess. If the washer is on an upper floor, close the supply valves behind it until the visit.
Can you replace a heating element in an electric dryer?
Yes. The technician first confirms the element is the failed part by testing it for continuity along with the high-limit thermostat and thermal fuse that protect it, since a tripped cutoff produces the same cold drum. Because a restricted vent is the most common reason an element burns out, the vent run is checked before the new element goes in (see the dryer questions further down this page). Gas dryers rely on different heating parts: the igniter, the flame sensor and two gas valve coils.
Can you replace a worn door seal on a refrigerator or freezer?
Yes. When the gasket tears, flattens or pulls away, warm humid air enters the cabinet. Typical signs are frost on the interior walls, moisture beading along the edge of the door, or a compressor that seems never to switch off. A sagging door can often be realigned, or a loose gasket reseated, without any new part. If replacement is necessary, the gasket must be the one specified for your model, so a photograph of the model label at the time of booking allows us to order it before the visit.
Can you repair an ice maker that has stopped producing ice?
Yes, both refrigerator ice makers and freestanding under-counter units. Frequent causes include a frozen fill tube, a faulty water inlet valve, a clogged water filter, or an ice maker module that has stopped finishing its harvest cycle. Our technician starts by checking the water supply, because a partly closed valve behind the refrigerator produces exactly the same symptom as a failed ice maker.
My microwave operates but does not heat. Is it repairable?
Frequently, yes. When the light is on and the turntable rotates but food stays cold, the high-voltage circuit has failed. The component responsible is usually one of four: the magnetron, the capacitor, the high-voltage diode or a door switch. Please do not attempt this repair yourself, because the capacitor can retain a dangerous charge long after the unit is unplugged. For a small countertop model, the repair may approach what a replacement would cost, and we will say so before any work begins.
Can you repair a dishwasher door that drops open?
Yes. When a dishwasher door drops open or refuses to hold its position, the cause is almost always a broken spring or hinge cable. Our technicians replace the springs as a pair, since the remaining one has worn to the same degree. The work is brief, although on some models the dishwasher must be eased out of its opening to reach the springs.
Can you repair a wine cooler that does not stay cold?
Yes, both compressor-based and thermoelectric models. On compressor units, the first items to check are a dusty condenser, a failed fan or the start relay; a slow refrigerant leak is a less frequent cause. Thermoelectric models depend on a Peltier module and small fans, so a warm room alone can leave them unable to hold temperature. Built-in units often fail for a simple reason: the ventilation grille at the front has been blocked.
Can you repair a refrigerator compressor?
In some cases. Often the compressor itself is sound and a component that starts or powers it has failed, such as the start relay, the overload protector or, on newer refrigerators, the inverter board. Those are quick replacements. A compressor that has genuinely failed is a larger job: our technician recovers the refrigerant, brazes in the replacement and recharges the system, all under EPA Section 608 requirements. On an older entry-level refrigerator the cost can exceed what the refrigerator is worth, and our technician explains this before any work starts.
Can you repair a cracked glass cooktop?
Usually, by replacing only the glass surface. Radiant and induction cooktops generally treat the glass as its own replaceable part, and it must match your exact model, because the heating elements and sensors are positioned immediately below it. Please do not use a cracked cooktop until it has been repaired, as spills can pass through the crack and reach live wiring.
My washer drum knocks loudly or will not turn. Is it repairable?
Yes. On a top-loading washer, knocking during the spin cycle usually indicates worn suspension rods or shock absorbers. On a front-loader, the cause is often the drum bearings, which also produce a roaring noise as the drum gains speed. Bearing replacement takes longer because the tub has to be taken apart, so for an older machine our technician sets the cost of that repair beside the price of a new washer before proceeding.
Can you repair a dryer drum that does not rotate?
Yes. A humming motor with a motionless drum usually means the belt has snapped or slipped off its pulley. When the dryer shows no response at all, our technician tests the door switch and the thermal fuse before anything else. A persistent squeal is typically an early warning from worn drum rollers or an idler pulley, which will eventually seize. Our technicians routinely carry belts, rollers and fuses.
Do you service induction cooktops and ranges?
Yes. Most induction faults are electronic, involving the power board, a temperature sensor beneath one of the coils, the cooling fan or the touch panel, and many display an error code first. If you read us the displayed code along with the model number at booking, the likely part can often accompany the technician on the first visit.
Does this describe your appliance?
8 questions · answered here
Repair or replace?
Expected service lives, and a practical method for judging when replacement is the sounder choice.
Is my refrigerator worth repairing?
In many cases, yes. Fans, defrost components, thermostats and control boards are all reasonable candidates for repair. As a general guide, if a repair would come to roughly half of what a similar new refrigerator costs and yours is well into its expected service life, replacement is usually the wiser choice. Built-in and panel-ready refrigerators are different: for them, repair is almost always the better option.
What is the typical lifespan of a dishwasher, and is mine worth repairing?
Published estimates generally suggest a service life of about nine to ten years. Until then, it is worthwhile to replace a failed pump, door spring, latch, water valve or heater. After that point, a leaking tub or a failed control board usually indicates that replacement is the better course. Where the water supply is on the hard side, keeping rinse aid filled and the hardness setting correct slows scale on the heating element and spray arms and helps a dishwasher reach the end of that range.
Is a faulty dryer worth repairing?
In nearly every case. Dryers are mechanically simple, and their wearing parts, including belts, rollers, fuses, elements and igniters, are inexpensive. Replacement becomes the better option if the drum has rusted through, or if the main control board fails on a very old unit. If the vent is obstructed, a new dryer will develop the same problem as the old one.
How long should a washing machine last, and when is replacement the better choice?
Expect roughly ten years of service, or fewer where a large household washes a load every day. A new door lock, lid switch, water valve, belt or drain pump is a routine repair and well worth doing. When an older front-loader needs new drum bearings, or the outer tub has cracked, replacement is generally the more sensible decision.
Is my oven, stove or range worth repairing?
In most cases, yes. A range typically lasts 13 to 15 years, and the components that wear over that time, such as the igniter, bake element, oven temperature sensor and switches, are not costly. Gas ranges frequently outlive their control boards, and fitting a new board to an otherwise sound range is a sound investment. Repair is nearly always justified on professional-style and dual-fuel ranges.
Should I repair or replace an over-the-range microwave?
Repair is more often justified than with a countertop model. An over-the-range unit also serves as your range hood and is fixed beneath the cabinets, so replacement involves both a new unit and installation. Replacing a failed fan, diode, door switch or magnetron is therefore usually the less expensive path. These units typically last about nine years. For a countertop microwave that no longer heats, a new unit is often the more economical choice.
Is my freezer worth repairing?
Chest and upright freezers are designed for a long service life. A faulty thermostat, defrost component, fan or door gasket is worth repairing at almost any age; the usual exception is a compressor failure in an older freezer. Until our technician arrives, keep the door closed, since a full freezer holds its temperature longer than a partly empty one.
Is it worth repairing a wine cooler?
For built-in or dual-zone models, generally yes, because any replacement has to fit the existing opening in your cabinetry. Small freestanding thermoelectric coolers are another matter, since the price of a new Peltier module comes close to that of a whole replacement cooler. On compressor-based coolers, a failed fan, relay or thermostat is worth repairing at almost any age.
Would you like a technician to assess your appliance?
4 questions · answered here
Coverage across Greater Houston
The communities and ZIP codes within our service area, how visits are scheduled across the metro, and the busy summer season to plan for.
Which parts of the Houston area do you cover?
Our service areas run across Harris County, with Sugar Land and Missouri City in Fort Bend County and Pearland in Brazoria County. Inside the Loop that means Downtown, Midtown, Montrose, the Heights, River Oaks, West University Place and Bellaire. Further out we cover Meyerland and Braeswood, the Galleria and Uptown, Memorial, Spring Branch, the Energy Corridor, Katy, Cypress, Spring, Humble and Atascocita, Pasadena and Clear Lake. Each service area page lists its ZIP codes.
Why do you give an arrival window instead of an exact time?
Our technicians cross the area on I-10, the 610 Loop, Beltway 8, I-45, US-59 and 290, where a single wreck or a summer thunderstorm can add half an hour without warning. So we book a three-hour arrival window, confirmed with you by the dispatcher, instead of promising an exact minute, and the technician telephones you if circumstances change.
My home was rebuilt or raised after flooding. Can you help?
Yes. Homes rebuilt or elevated after Harvey in 2017, or after other flooding in areas such as Meyerland and along the bayous, often have appliances on a new floor level, longer dryer vent runs, and water, drain and gas connections that were redone during the rebuild. Our technicians inspect those connections as well as the appliance, because after a move or a rebuild the machine is frequently sound and the fault lies in its hookup.
What should I do about my appliances after a hurricane or long power outage?
Keep refrigerator and freezer doors closed while the power is out. When it returns, give each appliance a few minutes before switching it back on, and watch for one that will not start, clicks repeatedly, shows an error code or smells hot, since restoration surges and brownouts can damage control boards and start relays. If an appliance has stood in floodwater, do not power it up at all; call us or your insurer first.
184 ZIP codes across 42 areas in Harris, Fort Bend, Brazoria, Montgomery, Galveston and Waller counties. See the complete list of communities served.
Need to confirm that we serve your address?
15 questions · answered here
Your appliance
Questions homeowners raise about specific appliances, with an explanation of what is usually responsible. Several describe normal operation rather than a defect.
Refrigerator
Refrigerator repair page →The freezer is cold but the fresh-food section is warm. Has the compressor failed?
That is unlikely. A cold freezer shows that the refrigeration system itself is working, and the problem is that chilled air is not reaching the fresh-food compartment. Usually the evaporator coil behind the freezer panel has become blocked with ice because a defrost heater, defrost thermostat or defrost timer has failed, or the evaporator fan has stopped. These are among the less costly refrigerator repairs, even though they are frequently mistaken for a compressor failure.
What does a typical refrigerator repair involve?
Refrigerator repairs fall into two broad categories. The first covers fans, defrost components, thermostats and control boards, which are common and reasonably priced. The second is sealed-system work, such as repairing a refrigerant leak, clearing a restriction or replacing the compressor, which costs considerably more and is often not worthwhile on an older entry-level model. The diagnostic visit establishes which category applies, and you receive the price before making any decision.
Why does the refrigerator in my garage keep malfunctioning?
Most refrigerators are designed for an air-conditioned room, and an attached Houston garage can stay well above that through the summer and into the evening. The condenser cannot shed heat fast enough, the compressor runs almost continuously and the fresh-food side drifts warm in the late afternoon. On the rare hard-freeze night, a single-thermostat model can do the opposite: sense the cold, stop running and let the freezer thaw. Refrigerators rated for garage installation are built for these conditions, and no repair can convert a standard model into one.
Washer
Washer repair page →My washer will not spin. Has the motor failed?
That is unlikely. A washer is designed not to spin while water remains in the tub, so the underlying fault is usually in the drain. Begin by checking the drain filter, where a sock or a coin is a far more common cause than a failed motor or control board. If the drain is clear, our technician next tests the lid or door lock, followed by the drive coupling or belt.
Will an error code tell you exactly which part has failed?
Not on its own. An error code reports what the washer detected, not the underlying cause. A fill code, for example, only indicates that water did not arrive within the expected time, which could result from low supply pressure, a blocked inlet hose screen, a worn water valve or a faulty level sensor. For that reason we test each possible cause before ordering a part.
What causes the odor in my front-loading washer?
The odor comes from water that has remained where it should not, typically in the sump, the drain filter or the drain hose, together with residue that builds up on the rubber door seal. Front-loaders are more prone to this because the seal stays damp between washes. Wiping the seal, leaving the door ajar after each cycle and cleaning the filter regularly will help. If the odor persists, it is advisable to have the drain inspected before the problem develops further.
Dryer
Dryer repair page →Why has the replacement heating element in my dryer also failed?
In most cases the venting is the underlying cause. A dryer depends on a strong flow of air, and when the vent is blocked or crushed, the element overheats and repeatedly trips its safety cutoff until it fails. A new element installed on the same restricted vent will fail in the same way. Our technicians measure the airflow, and if the vent run is longer than your dryer is rated for, we will tell you.
Is dryer repair usually expensive?
Generally it is not. The parts that wear on a dryer, such as belts, thermal fuses, drum rollers, heating elements, igniters and idler pulleys, cost relatively little, and the labor involved is straightforward. The more costly situation is a dryer that works correctly but is connected to a poor vent. Cleaning or rerouting the ductwork is separate work, and replacing dryer components will not resolve it.
Why does a single load take two or three cycles to dry?
The vent is nearly always responsible. In many two-story Houston houses and townhomes the laundry is upstairs or in an interior closet, so the duct climbs through the attic and exits at the roof, with several elbows along the way. Lint settles at every bend and in the roof cap, and a section can sag or separate in the attic. Add a flattened foil connector behind the machine and very little air can escape. The heating system may be working perfectly while the laundry still comes out damp.
Dishwasher
Dishwasher repair page →My dishes are still wet when the cycle ends. Has the heater failed?
Not necessarily. Many Bosch, Miele, ASKO and other European dishwashers have no drying element at all. They rely on moisture condensing on the cooler stainless steel tub, so plastic items commonly remain damp. This is normal behavior and not a fault.
What causes a white film on my glassware?
Usually one of three things: hard water, too much detergent, or an empty rinse aid reservoir. Water in the Houston area is moderately hard in many neighborhoods, but it varies with the supply, whether that is City of Houston surface water, a suburban groundwater well field or a MUD system, and your provider's annual water quality report is the place to check. A film that wipes off with vinegar is mineral; a film that will not come off is usually etching from excess detergent. Our technician sets the hardness and rinse aid settings to suit your supply where your model provides them.
Why is the upper rack not cleaning properly?
The fault usually lies in the components that deliver water to that level. The upper rack is cleaned only when water reaches its spray arm, so a jammed diverter or a blocked supply tube leaves the top rack dirty even though the bottom rack comes out clean. Before considering the pump, our technician turns each spray arm by hand, clears the nozzles and tests the diverter.
My oven does not reach temperature, yet the element appears intact.
Two possibilities should be considered first. The first is calibration: the oven may be heating normally but to a set point that has drifted, and on many models this is corrected through the settings rather than with a new part. The second is the door: a worn gasket or weakened hinges allow heat to escape faster than the element can replace it, which closely resembles a heating fault.
What does a typical oven repair involve?
Most oven repairs come down to one of a few parts: the temperature sensor, the bake element, the broil element, the igniter or a switch. These parts are moderately priced and the work is uncomplicated. Wall ovens require more labor because the unit must be removed from its cabinet safely, but that same installation is the reason a wall oven remains worth repairing far longer than a freestanding range.
There is a smell of gas near my oven. What should I do?
Switch the oven off and do not use it. If the odor is strong, bring everyone outside, avoid operating any light switches, and from outside the house contact your gas utility or 911. Once the utility has been notified, call us. Our technician closes the appliance's gas valve and tests every connection with an electronic gas detector. Should the leak turn out to be in the household piping rather than the oven, the valve stays closed and we explain the situation to you.
If your appliance is not listed above, consult the complete list of appliances we service ; each has its own page describing its usual faults.
Is your fault not described here?
2 questions · answered here
Buildings, gas and refrigerant
Requirements in high-rise condominiums and managed buildings, contractor documentation, gas connections and refrigerant handling.
Do you work in high-rise condos, apartments and gated communities?
Yes. Many high-rise buildings in Downtown, Midtown, Uptown and the Galleria area ask contractors for paperwork before granting access, and some only allow work at set hours with a reserved service elevator or loading dock. Gated neighborhoods may need a visitor code. Please let us know your building's or community's requirements when you book, and we will confirm which documents we are able to supply ahead of the appointment.
What precautions do you take with gas and refrigerant?
Our technicians follow established procedures for both. Before working on a gas appliance they close its supply valve, and once the work is complete they leak-test each fitting that was disturbed before the appliance goes back into use. Sealed-system repairs, where refrigerant must be recovered or recharged, follow the EPA Section 608 rules for handling refrigerant.
Does your building require contractor documentation?
6 questions · answered in context
Scheduling, price and warranty
How appointments are arranged, how the price is set, calling outside business hours, and the terms of our warranty.
- How quickly can a technician reach me?Built-in kitchens
- How is the cost of a repair worked out?Cost
- Are the phones really staffed around the clock, and is there an evening surcharge?Cost
- What warranty comes with the repair?Cost
- Will you advise me when a repair is not sensible?Cost
- What details help when I telephone you?Cost
Every completed repair is covered by our 90-Day Parts & 30-Day Labor Warranty. Our contact page describes the process in order, from the first call to the completed repair.
Ready to arrange an appointment?
5 questions · answered in context
In your home
Access to the home, floor protection, building documentation, and servicing more than one appliance in a single visit.
- Must someone be present during the visit?Built-in kitchens
- Do your technicians protect the floors?Built-in kitchens
- My building or HOA requires paperwork before contractors can enter.Built-in kitchens
- Can the technician examine a second appliance during the same visit?Built-in kitchens
- Will you repair an appliance that another company installed?Built-in kitchens
Is access to your appliance difficult?
5 questions · answered in context
In a commercial kitchen
Scheduling priority, visits planned around service hours, parts availability, and invoicing for business records.
- How quickly can you attend a restaurant?Commercial
- Can visits be arranged outside our peak service hours?Commercial
- Which commercial manufacturers do you service?Commercial
- Why does the same component keep failing on our cooler?Commercial
- Will we receive documentation for our records?Commercial
Is commercial kitchen equipment out of service?
Question not answered?
Unusual cases are best discussed by phone
A reference cannot anticipate every situation. An older model may need parts that are difficult to source, or an appliance may be installed in an awkward location. Describe the circumstances on a call and we will explain how we would approach them.