Jump to main content

Appliance repair across Greater Houston

Range and stove repair in Houston, both halves, gas or electric.

A range shares one supply, and often one control board, between its cooktop and its oven, so a single fault can take out both. We trace it from the supply inward.
  • Fault found before any price
  • One fixed price you approve
  • 90-day parts warranty

Free to request · 3 steps

Request a repair appointment

Takes about a minute. There is no charge to submit a request.

Prefer to call?(832) 476-8009
Step 1 of 3: Appliance and fault

Appliance and fault

01Which appliance needs attention?
02What is it doing?
Diagnosis
The cause is identified before any price is given
Approval
One fixed price, and work begins only with your consent
Hours
Our phones are answered 24 hours a day
Warranty
Parts warranted for 90 days, labor for 30
1–2.5 hours
Usual duration of a visit
45
Range & Stove faults documented
30
Manufacturers serviced
24/7
Phones answered

Range & Stove problems

Range and stove faults

Find the symptom, whether it's on the burners or in the oven. Each card lists the usual causes and how we confirm one.

  • Range oven stays coldThe surface burners or elements work normally, yet the oven heats very slowly or not at all. Since both sections draw from the same supply, a working cooktop shows that power or gas is reaching the range. That narrows the problem to the oven's own heating circuit.

    Usual causes

    • An electric bake element that has burnt through
    • A gas oven igniter that has lost the strength to open its valve
    • A failed oven safety valve
    • An open-circuit temperature sensor
    • A bake relay on the control board that will not close

    What we do

    With the control calling for heat, our technician checks whether voltage arrives at the bake element or igniter. On a gas range, the igniter's current draw is measured and compared with the rating the valve requires. The faulty component is replaced, and the oven is then brought to 350°F with a thermometer placed inside to confirm accurate heating.

  • One cooktop burner not workingA single burner or element on the cooktop stays cold while the others work as they should. That pattern points to a fault confined to that one position, such as its element, control switch, gas valve or igniter.

    Usual causes

    • A radiant or coil element that has burnt out
    • A failed infinite switch for that position
    • Clogged gas burner ports
    • A cracked igniter
    • A burnt element socket

    What we do

    Our technician tests the element or igniter together with the switch or valve that supplies it. Blocked burner ports are cleaned, and whichever element, switch, socket or igniter has failed is renewed. We then run the burner at low, medium and high settings to confirm steady operation.

  • Range control board malfunctionSymptoms of a board fault include the oven heating while switched off, error codes on the display, or no response to any input. Many ranges use one board for the oven and sometimes for the cooktop as well. Because sensors, keypads and wiring can imitate a board failure, the board is the last part we condemn.

    Usual causes

    • A relay that has welded shut or burnt
    • Heat damage after a self-clean cycle
    • An electrical surge
    • Moisture from a boil-over

    What we do

    Using the wiring diagram, our technician checks every board input and output, eliminating sensors, keypads and wiring along the way. Only a board confirmed as faulty is replaced. Afterwards the range is tested on bake, broil and each cooktop position.

  • Gas burner clicks but won't lightA burner may click repeatedly without igniting, or make no clicking sound at all. When this follows a spill or a cleaning, a misplaced cap or a damp igniter is the usual explanation. If none of the burners click, the spark module is the more likely fault.

    Usual causes

    • Burner cap not seated correctly
    • Igniter wet or coated with residue
    • Failed spark module
    • Blocked burner ports

    What we do

    Our technician dries and cleans the burner and igniter, then seats the cap properly. If there is still no spark, the spark module and burner switches are tested and the faulty part is replaced. We light every burner before the visit ends.

  • Smell of gas near the rangeA brief odor of gas as a burner ignites is expected. A persistent smell with every control off is not, and it should be taken seriously. If the odor is strong, everyone should go outdoors first; only then, from outside, call your gas utility or 911.

    Usual causes

    • A loose fitting at the regulator or manifold
    • A leaking burner valve
    • An aged flexible gas connector
    • An oven safety valve that does not shut fully

    What we do

    Our technician checks every joint and valve using a gas detector and a leak-detection solution. Any leaking part is replaced, an old connector is upgraded, and the range must pass a complete leak test before we leave.

  • Self-clean cycle failsThe self-clean cycle may refuse to start, end early, or finish with the door still locked. Because the cycle reaches extremely high temperatures, it places heavy stress on the door lock, the sensor and the control board.

    Usual causes

    • A failed door lock motor
    • A blown thermal fuse
    • A sensor that reads out of range at high temperature

    What we do

    Our technician tests the lock assembly, the temperature sensor and the thermal fuse, and reviews the error history stored in the control. The failed part is replaced, and we give you our view on whether continuing to use self-clean is sensible for your range.

  • Oven temperature inaccurateFood comes out undercooked or overcooked even though the dial or display is set correctly. Every oven cycles a little above and below its set point. A consistent offset larger than roughly 25°F, however, should be corrected.

    Usual causes

    • A temperature sensor that has drifted
    • A sensor resting against the oven wall
    • A changed offset setting in the control

    What we do

    Our technician records the average oven temperature across several heating cycles and measures the sensor's resistance. A defective sensor is replaced, or, where the model permits it, the control's offset is recalibrated.

  • Broken oven door hingeThe oven door may sit crooked, drop open sharply or fail to close. Hinges carry the full weight of the door and gradually wear out. A damaged hinge also allows heat to escape from the cavity.

    Usual causes

    • A broken hinge spring
    • A bent hinge arm
    • A worn hinge receiver in the oven frame
    • Heavy cookware placed on the open door

    What we do

    Our technician removes the door and fits two new hinges so that both sides pull with equal tension, inspecting the frame receivers for wear. After rehanging and adjusting the door, we run a paper test along the gasket to make sure it seals evenly.

  • Range sits unevenlyWhen oil collects on one side of a pan or baked goods rise unevenly, the range is probably not level. The leveling legs may need adjustment, or the floor beneath it may be uneven.

    Usual causes

    • Leveling legs never adjusted
    • An uneven floor
    • A broken or missing leg

    What we do

    Resting a spirit level on the oven rack, our technician adjusts the range from front to back and side to side. Any broken leg is replaced, and the anti-tip bracket is engaged again so the range cannot tip forward.

  • Convection fan does not spinOn a convection setting, the fan at the rear of the oven cavity should turn. When it stays still, food cooks unevenly, and some ranges will also display an error code.

    Usual causes

    • A failed fan motor
    • A fan blade loose on its shaft
    • A failed convection relay on the control
    • A burnt-out convection element

    What we do

    With convection selected, our technician checks for power at the fan motor and turns the blade by hand to detect any resistance. A failed motor, loose blade or faulty relay is repaired, and a convection bake confirms that the fan and its element both operate.

  • Broil element not heatingThe upper element inside the oven no longer glows, so broiling is impossible. Preheating can also slow down, because many ranges rely on the broil element during the preheat stage.

    Usual causes

    • A burnt-out broil element
    • A failed broil relay
    • A loose element terminal
    • Element damage from grease splatter

    What we do

    Our technician checks the element for continuity and confirms whether voltage reaches its terminals in broil mode. After the faulty element or relay is renewed, we operate broil for several minutes and confirm that preheat times are back to normal.

  • Oven overheats or won't turn offThe oven climbs well above its set temperature, or continues to heat once it has been turned off. A stuck relay of this kind is a safety hazard. If heating continues with the oven off, switch off its circuit breaker until it has been inspected.

    Usual causes

    • A control relay stuck in the closed position
    • A sensor reading lower than the true temperature
    • A disconnected temperature sensor

    What we do

    Our technician measures the cavity temperature with an independent probe and watches for the bake relay to open once the set temperature is reached. A relay stuck closed generally requires a replacement control board, while a faulty or disconnected sensor is replaced or reconnected. A complete cycle is then run to confirm the oven holds temperature.

  • Range trips the circuit breakerThe breaker trips as soon as a burner or the oven is switched on. This usually indicates an element that is shorting or a wire that has been damaged.

    Usual causes

    • A shorted element
    • A burnt terminal block
    • A damaged power cord
    • Moisture inside a surface element

    What we do

    Our technician disconnects each element in turn and tests it, along with the terminal block and power cord, for any short to ground. We renew the faulty component and repair any wiring damaged by heat, and current draw is measured with the oven and burners operating.

  • Oven door stuck lockedFollowing a self-clean cycle or a power cut, the oven door may remain locked. A failed lock motor or lock switch is the usual cause.

    Usual causes

    • A failed lock motor
    • A faulty lock switch
    • A control fault
    • Oven still hotter than its unlock temperature

    What we do

    Our technician allows the oven to cool fully and then attempts a lock reset through the control. If the door still will not release, we release the latch manually through the rear panel, then renew and test the lock motor or switch.

  • Cracked or shattered door glassThe oven door glass has cracked or broken apart. If the inner panel is damaged, please avoid using the oven until the glass has been replaced.

    Usual causes

    • Cold water striking hot glass (thermal shock)
    • Impact from a pan or rack
    • Stress from self-clean temperatures
    • A chip along the glass edge

    What we do

    Our technician disassembles the door, removes all broken glass and installs a matching tempered glass panel. The door is reassembled, rehung and checked for correct alignment and an even seal.

  • Worn oven door sealHeat escapes around the edges of the oven door. As a result the oven takes longer to heat and food cooks unevenly.

    Usual causes

    • A hardened gasket
    • A torn gasket
    • Broken gasket clips
    • Gasket damage from self-clean heat

    What we do

    Our technician installs a gasket made for your model and secures every clip. A paper test confirms that the door seals evenly, and the preheat time is measured afterwards.

Show 29 further range & stove faults
  • Oven takes too long to preheatA typical oven preheats in about 10–15 minutes. When it takes considerably longer, a heat source may be weakening or the door gasket may be leaking.

    Usual causes

    • A weak igniter on a gas model
    • A failed broil element on an electric model
    • A leaking door gasket
    • A drifting temperature sensor

    What we do

    Our technician times the preheat and tests each heat source, including the broil element that many ranges use while preheating. Once the weak component has been renewed, we time a second preheat for comparison.

  • Heavy smoke from the ovenMost heavy smoke comes from food spills burning in the cavity. Smoke that originates from wiring or the controls is a more serious matter and should be inspected promptly.

    Usual causes

    • Spills on the oven floor
    • Grease on the broil element
    • Overheating wiring
    • A shorting element

    What we do

    Our technician locates where the smoke is coming from and examines the wiring, elements and terminals. Any component showing damage is renewed, and where spills are the only cause, we explain how to clean them safely.

  • Weak gas oven igniterThe igniter glows, yet the oven lights slowly or not at all. A weakened igniter cannot pass the current the gas valve needs before it will open.

    Usual causes

    • Igniter worn through age
    • A cracked igniter
    • A loose igniter connector

    What we do

    Our technician measures the current the igniter draws in the circuit and compares it with the rating of the safety valve. After a weak or cracked igniter is renewed, we light the oven several times in succession to confirm reliable ignition.

  • Failed gas oven safety valveThe igniter operates correctly but no gas reaches the oven burner. In that situation the safety valve itself may have failed.

    Usual causes

    • A failed valve coil
    • A valve stuck closed
    • An igniter lacking the current to open the valve

    What we do

    Our technician tests the valve using an igniter known to be good and checks the valve coil directly. A defective valve is replaced, and the range then receives a complete leak test.

  • One oven of a double failsOn a double-oven range, one cavity works while the other does not. Each oven has its own heat source and temperature sensor, so the fault is usually limited to the cavity that has stopped.

    Usual causes

    • A failed element or igniter in one cavity
    • A failed sensor for that oven
    • A failed board relay for that oven
    • A faulty door switch for that oven

    What we do

    Our technician tests the heat source, sensor and relay of each oven independently. Once the failed part is replaced, both ovens are run together to confirm they heat correctly at the same time.

  • Display shows incomplete digitsPortions of the numbers on the range display no longer light up. This generally indicates that the display board is beginning to fail.

    Usual causes

    • A failed display board
    • Heat damage from self-clean
    • A loose ribbon cable
    • Moisture behind the control panel

    What we do

    Our technician reseats the ribbon cable and tests the display board and control board. The faulty component is replaced, and the clock and every function are checked.

  • Range dead after a power cutFollowing a storm or an outage, the range does not power back on. An electrical surge may have damaged the control or blown its fuse.

    Usual causes

    • A tripped breaker
    • A blown control fuse
    • A board damaged by a surge
    • A loose terminal block connection

    What we do

    Our technician confirms both legs of the supply at the breaker and the terminal block, then tests the control fuse and board. Damaged parts are replaced and every range function is checked.

  • Faulty surface element switchThe element heats only on its highest setting, or does not respond when the knob is turned. In either case the switch behind the knob has usually failed.

    Usual causes

    • Burnt switch contacts
    • A switch stuck in one position
    • A loose terminal on the switch

    What we do

    Our technician tests the switch at every setting and inspects its terminals for scorching. After a failed switch is renewed, we confirm the element works on low, medium and high.

  • Scorched range cord or outletThe range loses power intermittently, or scorch marks are visible around the plug. A loose electrical connection can overheat and should be dealt with without delay.

    Usual causes

    • A loose terminal block connection
    • Corroded terminals
    • An aged power cord
    • A worn wall outlet

    What we do

    Our technician fits a new power cord and tightens the terminal block connections. If the wall outlet itself has been damaged, we advise you to have a licensed electrician replace it.

  • Induction zone won't detect panThe cooking zone flashes but does not heat. Often the pan is not magnetic, or it is too small for the zone to recognize.

    Usual causes

    • A pan that is not magnetic
    • A pan too small for the zone
    • A pan-detection sensor fault
    • A power board fault

    What we do

    Our technician tests the zone with an induction-compatible pan known to work and runs the range's diagnostic mode. If the cookware is not the cause, the sensor or power board is replaced.

  • Dual-fuel range oven not heatingOn a dual-fuel range the burners run on gas while the oven heats electrically. Because the two run on different energy sources, the oven can fail while the gas burners keep working.

    Usual causes

    • A failed bake element
    • A sensor fault
    • A control fault
    • Loss of one leg of the 240-volt supply

    What we do

    Our technician verifies the 240-volt supply to the oven, then tests its elements, temperature sensor and control. Once the faulty part has been renewed, we heat the oven and confirm it reaches temperature.

  • Range not set up for propaneFlames that are oversized or yellow can mean the range was never converted for propane use. Burning propane through natural-gas settings produces an incorrect flame.

    Usual causes

    • Natural-gas orifices still fitted
    • A regulator not converted
    • An oven orifice left unchanged

    What we do

    Our technician completes the propane conversion at the cooktop burners, the oven and the regulator, then adjusts and checks every flame. A full leak test is carried out before we finish.

  • Cooling fan runs after shutoffA cooling fan often continues running for a while after the oven is turned off, and that is normal until the oven cools down. If it keeps running for hours, a component may be stuck.

    Usual causes

    • Normal cooldown operation
    • A cooling thermostat stuck closed
    • A stuck fan relay

    What we do

    Our technician checks how long the fan continues after shutoff and tests the thermostat and relay that control it. If the fan runs well beyond the point at which the oven has cooled, the stuck part is replaced.

  • Oven shuts off while cookingThe oven switches itself off partway through a bake. Possible explanations include an automatic shut-off feature, an overheating cutout or a control that is beginning to fail.

    Usual causes

    • An automatic shut-off setting
    • An overheating cutout tripping
    • A control fault
    • A loose connection

    What we do

    Our technician reviews the automatic shut-off setting, tests the thermal cutouts and sensors, and inspects the wiring connections. After the faulty part is renewed, we run an extended bake to confirm the oven stays on.

  • Stove tips forwardThe stove lifts or tilts forward when the oven door is opened or weight is placed on it. An anti-tip bracket is meant to hold the rear leg in place. Without one, a stove can fall forward, which is a particular danger if a child climbs on the open door.

    Usual causes

    • Bracket removed during a move or flooring work
    • Rear leg not engaged in the bracket
    • Uneven floor
    • Rear leveling leg raised too high to catch the bracket

    What we do

    Our technician secures the anti-tip bracket, either new or existing, into the floor or wall and adjusts the rear leg so it slides beneath it. The stove is then leveled, and we confirm it stays put with weight applied to the open door.

  • Yellow flame on one burnerOne burner produces a yellow, sooty flame while the rest burn blue. The burner may be dirty, its cap may be out of position, or the air-to-gas mixture may be wrong.

    Usual causes

    • Dirty burner ports
    • Misaligned burner cap
    • Air shutter out of adjustment
    • Partly obstructed orifice

    What we do

    We clean the burner, the orifice and the ports, seat the cap properly and adjust the air shutter on models that have one. The flame is observed on high and low until it burns steady and blue.

  • Pilot goes out when knob releasedWhere a stove has a standing pilot, the gas valve is held open by a thermocouple for as long as the pilot is burning. When the thermocouple fails, the pilot goes out as soon as you let go of the knob.

    Usual causes

    • Worn thermocouple
    • Pilot flame too small to warm the thermocouple tip
    • Dirty pilot orifice
    • Loose connection at the safety valve

    What we do

    Our technician cleans the pilot orifice and confirms the flame envelops the tip of the thermocouple. We replace a worn thermocouple and secure its connection, and the pilot is lit and left burning to confirm it remains on.

  • Standing pilot keeps going outAn older stove's standing pilot is repeatedly going out. A draft, a dirty pilot assembly or a flame set too low is usually responsible.

    Usual causes

    • Clogged pilot orifice
    • Draft from a nearby window, door or fan
    • Pilot adjusted too low
    • Grease built up around the pilot

    What we do

    We clean the pilot and adjust it to a steady flame of the correct size, and we look for drafts in the area. The pilot is relit and observed for several minutes while the burners are switched on and off.

  • Gas burners need power to lightElectronic ignition cannot spark without electricity. During a power outage, the burners on many gas stoves can be lit carefully with a match, but ovens that use a glow-bar igniter will not light until power returns.

    Usual causes

    • Power outage
    • Power cord unplugged
    • Tripped receptacle or GFCI
    • Blown fuse on the spark module

    What we do

    We check the receptacle, the cord and the stove's internal power circuit. We also explain how the burners on your particular model can be lit safely by hand during an outage, and which parts will not operate without electricity.

  • Low flame will not holdOn its lowest setting the flame either goes out or remains too high to simmer. The low-flame adjustment on the burner valve may need resetting.

    Usual causes

    • Simmer adjustment screw out of position
    • Dirty burner ports
    • Incorrect setup after a gas conversion
    • Burner cap out of place

    What we do

    After cleaning the burner, we reset the simmer adjustment on the valve. The flame is then checked on the lowest setting to confirm it stays lit without running too high.

  • Electric element will not turn offAn electric element remains on full heat even with the knob at a low setting or off. This presents a fire risk, so switch off the stove's breaker until it has been repaired.

    Usual causes

    • Welded contacts in the infinite switch
    • Short in the wiring
    • Switch melted by a loose terminal

    What we do

    With the breaker off, our technician replaces the switch and examines the surrounding wiring for heat damage. The element is then tested at every setting to confirm it switches off completely.

  • Igniter keeps clicking after lightingSome stoves are designed to reignite a burner automatically if the flame is lost. If the clicking continues while a flame is present, the stove is failing to detect that flame.

    Usual causes

    • Dirty igniter
    • Burner cap not seated
    • Fault in the spark module
    • Poor ground connection at the burner

    What we do

    After cleaning the igniter and seating the cap, our technician confirms the burner has a sound ground path and tests the spark module. Whichever of the module or igniter has failed is replaced.

  • Coil element sparks or cuts outA coil element sparks at its terminals or heats only intermittently. The receptacle it plugs into has often been burnt.

    Usual causes

    • Burnt receptacle
    • Element sitting loosely in the receptacle
    • Corroded terminals
    • Spills reaching the receptacle

    What we do

    We replace the receptacle, and the element as well if its terminals are pitted, because a damaged element will quickly burn a new receptacle. The wiring is inspected for heat damage and repaired where necessary.

  • Burner goes out after lightingThe burner ignites but goes out once you release the knob. On certain stoves a safety device must detect the flame before gas continues to flow.

    Usual causes

    • Faulty flame sensor or thermocouple
    • Burner cap out of position
    • Low gas supply pressure
    • Drafts extinguishing the flame

    What we do

    Our technician tests the flame sensor or thermocouple, checks the gas pressure and confirms the cap is seated. After the faulty part is replaced, we leave the burner on for several minutes to be sure it stays alight.

  • Knob turns freely without effectThe knob rotates but the burner does not respond. Either the knob or the shaft of the valve or switch has worn.

    Usual causes

    • Worn insert inside the knob
    • Stripped valve shaft
    • Broken switch shaft

    What we do

    We fit a new knob and inspect the shaft for wear. Where the shaft itself is damaged we replace the valve or switch, and a leak test follows whenever a gas component has been changed.

  • Display shows LOC lockThe oven does not respond to the controls and the display reads 'LOC', which usually means the control lock is active.

    Usual causes

    • Control lock activated
    • Fault in the keypad
    • Fault in the control board

    What we do

    Using the key sequence for your model, we release the lock and test the keypad. If the keypad or board is at fault we replace it before testing the oven.

  • Pots slow to come to boilWater now takes much longer to boil than it once did. The burner may have lost output, or the pan may not suit the burner.

    Usual causes

    • Clogged burner ports
    • Low gas pressure
    • Weak electric element
    • Pan too small or warped

    What we do

    On a gas stove we check the supply pressure and clean the burners; on an electric stove we test the element and its switch. We also check that your pans sit flat on the burner.

  • New stove gives off burning odorA new stove often produces an odor during its first few uses while protective factory coatings burn away. If the odor persists beyond that, packing material or a wiring fault should be ruled out.

    Usual causes

    • Factory coatings burning away
    • Packing material left inside
    • Wiring fault

    What we do

    We look for leftover packing material and check for wiring faults. We then recommend running the empty oven once at a high temperature so the remaining coatings can burn off.

  • Boil-over affecting burner controlsAfter a pot boils over, the burners may fail to light, click without stopping or behave erratically. Liquid has probably reached the spark switches.

    Usual causes

    • Water on the spark switches
    • Sugary residue on the switches
    • Corroded wiring
    • Liquid inside the burner box

    What we do

    Our technician dries and cleans the switches and the burner box, then tests each switch individually. Damaged switches or wiring are replaced, and all burners are tested afterwards.

Brands

Range & Stove manufacturers we service

All brands →
  • Samsung
  • LG
  • Whirlpool
  • GE Appliances
  • Maytag
  • Bosch
  • KitchenAid
  • Frigidaire
  • Viking
  • Kenmore
  • Amana
  • Electrolux
  • Miele
  • Thermador
  • Wolf
  • Admiral
  • AGA
  • Avanti
  • Bertazzoni
  • Blomberg
  • Dacor
  • DCS
  • Fisher & Paykel
  • Hotpoint
  • JennAir
  • La Cornue
  • Roper
  • Smeg
  • Thor Kitchen
  • Vulcan

Technical notes

Ranges and stoves in Houston kitchens

Houston has both gas and electric ranges in large numbers: plenty of homes have natural gas to the kitchen, and plenty of apartments, condos and townhomes are all-electric. Dual-fuel ranges put a gas cooktop over an electric oven and bring both sets of faults.

On an electric range, a 240-volt circuit feeds both halves; lose one leg at the breaker or burn a terminal block and the surface elements may still heat while the oven stays cold. On gas, the oven igniter and safety valve fail far more often than the burners above. Freestanding and slide-in ranges also need their anti-tip bracket in place; it is often missing after a range has been moved.

After hurricanes and outages

A range that is dead after a storm usually has a tripped breaker, a blown control fuse or a board hurt by the surge when power came back. Gas ranges with electronic ignition will not spark without power. Many manuals allow the surface burners to be lit carefully with a match during an outage, but gas ovens with glow-bar igniters will not work without electricity and should not be forced.

Burnt cords and terminal blocks

A range cord that is loose at the terminal block heats up every time the oven runs, and over time the block scorches. Warning signs are a burning smell at the back of the range, a flickering display or one half going dead. Turn off the breaker and call; this is not a fault to cook around.

What to check, and how range repairs are priced

Start by noting which half has the fault: the burners, the oven, or both. Both halves dead on an electric range points to the supply, such as a breaker or the terminal block, and a gas range that will not spark or light its oven may simply have lost power. Turn the range off at the breaker or close its gas valve and call if you smell gas, see scorching at the back, or the range rocks forward when the oven door is opened.

Igniters, elements, infinite switches and oven sensors are the common, moderate repairs. A gas oven safety valve, a dual-fuel control or a power board costs more, and on pro-style ranges model-specific parts raise every figure.

Questions

Range and stove questions we hear often

My gas burners light, but the oven won't. Why?

The surface burners use spark ignition while most gas ovens use a glow-bar igniter and a safety valve, so the two halves fail independently. A weak igniter is the most common cause, followed by the safety valve and, on electronic models, the control that powers the igniter.

Why do the burners on my electric range work but the oven doesn't?

A range runs on two 120-volt legs. Lose one at a breaker or a burnt terminal block and some parts get only half voltage, so elements may glow faintly or not at all while others work. If the supply is sound, the bake element, a relay on the board or the oven sensor is next.

What does a range anti-tip bracket do, and why does it matter?

It anchors the range to the floor or wall so it cannot tip forward when weight is put on an open oven door, a real danger with children in the house. Manufacturers require it, and it is often left off after a range is moved for cleaning or flooring work.

Do you service pro-style and dual-fuel ranges?

Yes, including pro-style ranges from makers such as Wolf, Thermador and Viking. They have more burners, larger ovens and more ignition parts than a standard range, and parts are model-specific, so the model number at booking lets us bring the right components.

Book a range or stove repair

Tell us gas, electric or dual-fuel, the model number and which half is failing. We'll confirm a three-hour window and bring the parts that model usually needs.

Call, any hour(832) 476-8009Book on the web