Jump to main content

Appliance repair across Greater Houston

Microwave repair in Houston, for over-the-range, built-in and drawer models.

Light on, turntable spinning, food still cold? That's the high-voltage circuit, and it is not a do-it-yourself job. We discharge it safely and test each part.
  • Fault found before any price
  • One fixed price you approve
  • 90-day parts warranty

Free to request · 3 steps

Request a repair appointment

Takes about a minute. There is no charge to submit a request.

Prefer to call?(832) 476-8009
Step 1 of 3: Appliance and fault

Appliance and fault

01Which appliance needs attention?
02What is it doing?
Diagnosis
The cause is identified before any price is given
Approval
One fixed price, and work begins only with your consent
Hours
Our phones are answered 24 hours a day
Warranty
Parts warranted for 90 days, labor for 30
1–2 hours
Usual duration of a visit
30
Microwave faults documented
28
Manufacturers serviced
24/7
Phones answered

Microwave problems

Microwave faults we repair

Choose the symptom. Each card lists what usually causes it and how we test the high-voltage parts safely.

  • Runs normally but food stays coldThe interior lamp lights, the plate turns and the countdown proceeds, yet the food is no warmer at the end. This tells us the high-voltage circuit is not producing microwave energy. Every component in that circuit can carry a lethal charge, so diagnosis should be left to a trained technician.

    Usual causes

    • A shorted high-voltage diode
    • A magnetron that has reached the end of its life
    • A failed high-voltage capacitor
    • An interlock switch that is not closing the heating circuit
    • An open thermal protector mounted on the magnetron

    What we do

    Once the capacitor has been discharged, our technician tests the diode, capacitor, transformer and magnetron individually. The interlock switches are checked as well, since a single faulty switch is enough to stop heating. After the defective part is replaced, a cup of water is heated to confirm normal output.

  • Sparks or flashes during cookingVisible flashes or a crackling sound while the oven runs usually begin with metal: a twist tie, foil or a dish with metallic trim. When nothing metallic is inside, the likely culprits are a burnt waveguide cover or damaged enamel on the cavity walls.

    Usual causes

    • Food residue carbonized on the waveguide cover
    • Enamel chipped away, leaving bare metal exposed
    • A metal rack placed in an incorrect position
    • Decorative metal edging on a plate or bowl

    What we do

    Our technician examines the waveguide cover, the cavity walls and any supplied racks. A carbonized cover is replaced, chipped enamel is restored with paint rated for microwave use, and the unit is then operated to confirm that the arcing has ended.

  • Turntable plate stays stillWhen the glass plate does not rotate, food heats in uneven patches. Often the plate has simply slipped off its drive coupler. If it is seated correctly, the small motor beneath the cavity floor is the next suspect.

    Usual causes

    • The glass plate is not engaged on the drive coupler
    • The turntable motor has burned out
    • The roller ring is soiled or broken
    • The coupler has cracked

    What we do

    We first confirm the plate is seated on its coupler and the roller ring is clean and intact. If both are in order, the motor is tested from below for supply voltage and winding continuity. Whichever of the two has failed, motor or coupler, is renewed, and the plate is watched through a full minute of rotation.

  • Door does not latch shutThe door fails to close with a firm click, or the oven refuses to start because it cannot sense that the door is shut. Door hooks and latch springs see constant wear. A microwave must never operate with an unlatched door.

    Usual causes

    • A broken door hook
    • A missing or detached latch spring
    • The door sitting out of line on its hinges
    • A cracked interlock switch holder

    What we do

    Our technician inspects the hooks, the latch spring and hinge alignment, then tests each interlock switch through the closing motion. Damaged hooks, springs or holders are replaced. Because the door forms part of the energy seal, a leakage meter reading is taken after any door repair.

  • Display dark or flickeringThe readout is blank or only partly illuminated, and the oven may or may not still operate. Before booking, it is worth checking the circuit breaker and trying the unit on a different outlet.

    Usual causes

    • A blown main line fuse
    • A failed power supply on the control board
    • A defective display board
    • Damage from an electrical surge
    • An interlock switch fault that caused the fuse to blow

    What we do

    Our technician measures the line fuse first and then the low-voltage feed to the control. When a fuse has blown, our technician identifies the reason, most often an interlock switch, before fitting a new one. Where a board is at fault, the control or display is renewed, after which clock settings, every key and heating output are each verified.

  • New grinding, buzzing or hummingA sound that was not there before deserves attention, although a steady low hum is normal. Grinding generally originates in the turntable drive or a fan. A pronounced buzz may indicate trouble with the magnetron or transformer.

    Usual causes

    • A worn turntable motor
    • A cooling fan blade that has worked loose
    • Worn bearings in the vent blower
    • A magnetron nearing failure

    What we do

    After discharging the capacitor and removing the cabinet, our technician turns the fans and turntable motor by hand, then runs the unit under controlled conditions to pinpoint the noise. A worn turntable motor, cooling fan or vent motor is replaced. If the buzz comes from a failing magnetron, we discuss whether replacement is worthwhile for your appliance.

  • Display works but will not startThe display is lit, yet pressing start produces no response. The interlock switches and the control are the usual sources. Please check first that the child lock has not been engaged.

    Usual causes

    • An interlock switch that is not being actuated
    • The child lock is active
    • A start key that no longer registers
    • A fault on the control board
    • An open thermal cutout

    What we do

    Our technician rules out the child lock, then tests each interlock switch and the start key on the membrane. The thermal cutouts and the control relay are checked next. The defective part is replaced, and the unit is run with a cup of water to confirm operation.

  • Operates with the door openIf the oven starts or continues running once the door is opened, stop using it and unplug it immediately. This means the safety interlocks have failed, and it should be treated as a serious hazard.

    Usual causes

    • An interlock switch whose contacts have fused closed
    • A failed monitor switch
    • A control board relay stuck in the closed position

    What we do

    We isolate the appliance and replace the complete set of interlock and monitor switches, rather than renewing a single switch. The control relay is then examined to make sure its contacts have not welded. Before the unit is returned to service, we confirm that it stops the instant the door opens and measure for energy leakage around the door.

  • Keypad buttons unresponsiveCertain keys respond while others do not, or the entire panel is unresponsive. Over time, steam and cooking grease can degrade the keypad membrane.

    Usual causes

    • A worn keypad membrane
    • A loose ribbon cable connection
    • A failed control board
    • Moisture inside the control panel

    What we do

    Our technician checks the keypad circuit with a meter and inspects the ribbon connector at the board. If the keypad tests sound, the board's input circuit is examined. The defective keypad or board is replaced, and each key is pressed to confirm it registers.

  • Interior or cooktop light outThe lamp inside the cavity or beneath the unit no longer lights. A spent bulb is the usual reason, and many over-the-range models use two or more.

    Usual causes

    • A burned-out bulb
    • A lamp socket damaged by heat
    • A failed light relay on the control
    • A faulty cooktop light switch on over-the-range units

    What we do

    We fit the correct appliance-rated bulb and test both the socket and the light output from the control. Should the socket show heat damage or the relay prove faulty, that part is renewed and the interior and cooktop lamps are each confirmed working.

  • Trips the breaker on startThe breaker shuts off the moment the oven starts. This can indicate a short in the high-voltage section, or the outlet may share its circuit with another heavy appliance.

    Usual causes

    • A shorted high-voltage diode or capacitor
    • A shorted magnetron
    • An overloaded shared circuit
    • An interlock switch fault shorting the supply line

    What we do

    With the capacitor discharged, our technician tests the diode, capacitor, transformer, magnetron and interlock switches for shorts. The faulty part is replaced. If the oven tests normal but shares its circuit with other appliances, we explain that and suggest consulting an electrician.

  • Error code on the displayCodes such as F1, F3 or SE indicate that the control has detected a problem, most often with a sensor or the keypad. The specific code helps narrow the diagnosis.

    Usual causes

    • A faulty humidity sensor
    • A short in the keypad
    • A defective thermistor
    • A control board fault

    What we do

    We look up the meaning of the code for your exact model and test the component it identifies, typically a sensor, thermistor or keypad. After the faulty component has been renewed and the code cleared, the unit is operated to confirm the fault does not return.

  • Burn mark on the inner side panelA dark or scorched patch appears on a small flat panel within the cavity, most often on the right-hand wall. That panel is the waveguide cover, and it absorbs grease that eventually carbonizes.

    Usual causes

    • Grease and food spatter absorbed into the cover
    • Operating the oven with nothing inside
    • Infrequent cleaning of the cover
    • A crack in the cover

    What we do

    Our technician installs a waveguide cover cut for your model and removes carbon deposits from the opening behind it. Our technician also inspects the surrounding enamel for scorching, and the unit is run with water to confirm the arcing has stopped.

  • Faulty door interlock switchSeveral switches work together to confirm the door is closed. When one fails, the oven may not start, may cut out during cooking, or may blow its fuse.

    Usual causes

    • Worn switch contacts
    • A broken switch actuator
    • Door hooks that no longer press the switch
    • A cracked switch holder

    What we do

    We test the primary, secondary and monitor switches through the door's full travel. The switches are replaced as a matched set, the line fuse is inspected and renewed if needed, and a leakage reading is taken around the door afterwards.

  • Broken or loose door handleThe handle has loosened or cracked, making the door awkward to open. In most cases this is a straightforward part replacement.

    Usual causes

    • Loose handle mounting screws
    • A cracked plastic handle
    • A broken latch lever
    • A broken spring behind the release button

    What we do

    Our technician renews whichever part is damaged, whether that is the handle, the latch lever or the spring behind the release button, and confirms the door opens smoothly. The hooks and interlock switches are tested at the same time, so the oven still shuts off whenever the door opens.

  • Internal cooling fan stoppedThis fan keeps the electronics and magnetron at a safe temperature. If it stops, the oven may overheat and switch itself off, and you may notice an odor of hot plastic.

    Usual causes

    • A failed fan motor
    • An obstructed or loose fan blade
    • A loose fan wiring connection
    • A thermal cutout tripping for lack of airflow

    What we do

    Our technician rotates the blade manually, then measures the motor windings and the voltage reaching them. If the motor has failed it is renewed, and the thermal cutouts are inspected as well, because a period without cooling may have tripped or weakened them. The oven is then run for several minutes to confirm it holds a safe temperature.

Show 14 further microwave faults
  • Clogged metal grease filtersOn over-the-range models, metal mesh filters trap grease rising from the cooktop. Once they clog, the vent blower moves less air and grease can accumulate inside the housing.

    Usual causes

    • Filters that have not been cleaned
    • Frequent frying on the cooktop below
    • Bent or damaged filter mesh
    • Grease accumulating inside the vent passage

    What we do

    Our technician removes and degreases the filters, or replaces any that are bent or torn, and confirms the blower draws air properly. The vent passage is inspected for grease buildup, which presents a fire risk, and we show you how to clean the filters yourself.

  • Charcoal odor filter worn outWhere the microwave recirculates air back into the kitchen, a charcoal filter absorbs cooking odors. This filter cannot be cleaned and gradually stops working.

    Usual causes

    • The filter has exceeded its service life
    • No grease filter in place, allowing grease onto the charcoal
    • An incorrect filter type installed
    • A unit configured for recirculation in a kitchen ducted outdoors

    What we do

    We install the correct charcoal filter and confirm that the blower is configured to match your kitchen, either recirculating into the room or exhausting outdoors. If the configuration is wrong, the blower is reoriented so smoke is actually removed.

  • Vent blower not workingThe blower beneath the microwave either does not run or runs very loudly, leaving smoke and steam from the cooktop in the kitchen.

    Usual causes

    • A failed vent motor
    • A faulty fan speed switch
    • A damper stuck closed
    • A failed control relay

    What we do

    Our technician tests the vent motor, speed switch and control relay, and checks that the exhaust damper opens freely. A failed motor or switch is replaced, a sticking damper is freed, and the blower is run at each speed to confirm airflow.

  • Heats only some of the timeHeating is unreliable: some days it works and others it does not, or it heats briefly and then stops. This pattern usually points to a failing component or a loose connection.

    Usual causes

    • An interlock switch with intermittent contact
    • The magnetron thermal cutout opening
    • A loose connection in the high-voltage circuit
    • A weakening magnetron

    What we do

    With full safety precautions in place, our technician runs the unit through repeated heating cycles with the cabinet removed, observing how the high-voltage circuit and each cutout behave. Once identified, the faulty switch, cutout or connection is put right, and the oven is tested heating water several times in succession.

  • Stops after a few secondsThe oven starts, runs briefly and then stops, often with the display still lit. A thermal cutout or interlock switch is commonly responsible.

    Usual causes

    • A thermal cutout opening due to overheating
    • An interlock switch losing contact
    • A cooling fan that is not running
    • Obstructed ventilation openings

    What we do

    We test the cutouts, interlock switches and cooling fan, and confirm the vents are unobstructed. Once the cause is corrected, the unit is run through a complete five-minute cycle to make sure it no longer stops early.

  • Burning or hot plastic odorAn odor of burning during or just after use may come from food residue, but it can also signal an overheating electrical component. If the smell is strong, stop using the appliance.

    Usual causes

    • A waveguide cover that is burning
    • Overheating wire insulation
    • A failing fan allowing components to overheat
    • A plastic container melting in the cavity

    What we do

    Our technician removes the cabinet and checks for melted insulation, scorched connectors and heat marks around the magnetron and the transformer. Any damaged wiring or component is renewed, the fan's operation is confirmed, and the oven is operated under observation for any odor or smoke.

  • Shuts off during long cookingThe oven switches itself off partway through longer cooking times. Built-in and over-the-range units rely on adequate airflow to stay within safe temperatures.

    Usual causes

    • Vents obstructed by cabinetry or stored items
    • A weak cooling fan
    • A thermal cutout that trips too early
    • Dust accumulated inside the cabinet

    What we do

    Our technician follows the path the cooling air takes, measures fan and cutout performance, and removes dust from inside the cabinet. If the fan or a cutout proves weak, it is renewed, and obstructed vents are opened so the oven can complete longer cycles.

  • Vent fan starts on its ownThe vent blower switches on while the microwave is idle. On over-the-range models this is frequently by design: a thermostat starts the fan when the cooktop below becomes hot. If the fan never stops, a thermostat or relay may be stuck.

    Usual causes

    • Rising heat from the cooktop activating the fan
    • A thermostat stuck in the closed position
    • A stuck relay

    What we do

    Our technician first determines whether cooktop heat is triggering the fan, which is a normal protective function. If the blower continues running with a cold cooktop, the thermostat and relay are tested and the stuck component is replaced.

  • Inverter model produces no heatSome microwaves use an inverter board in place of a conventional transformer. When that board fails, the oven stops heating and may also blow its fuse.

    Usual causes

    • A failed inverter board
    • A fuse blown as a result of the inverter fault
    • A failed magnetron
    • Damaged wiring between the inverter and magnetron

    What we do

    After discharging the system, our technician tests the inverter board and the magnetron. A failed board is replaced, the fuse is inspected, and the oven is checked at several power settings to confirm even heating.

  • Popping or crackling while heatingPopping can be caused by the food itself. If it occurs with nothing that would spatter, it may indicate arcing in the cavity or a problem in the high-voltage components.

    Usual causes

    • Arcing at the waveguide opening
    • Damaged cavity enamel
    • A failing high-voltage component
    • Foods with skins or fat that burst and spatter

    What we do

    We inspect the cavity and waveguide for scorch marks and test the high-voltage components. The damaged part is repaired or replaced, and the oven is run with water to confirm the popping has ceased.

  • Power level settings have no effectLower settings heat just as strongly as full power. At reduced settings the magnetron should switch on and off in cycles; when it does not, the control or a relay has likely failed.

    Usual causes

    • A control relay stuck closed
    • An inverter that is not modulating output
    • A control board fault
    • A keypad that does not register the power selection

    What we do

    Our technician tests the relay and inverter output at different settings while listening for the magnetron to cycle. Whichever component is responsible, relay, inverter or board, is renewed, and each power level is verified with a timed water test.

  • Sensor cooking programs misjudge timingAutomatic programs such as popcorn or reheat stop too soon or run too long. These programs depend on a humidity sensor that detects steam, and when it fails the timing becomes unreliable.

    Usual causes

    • A faulty humidity sensor
    • Grease coating the sensor opening
    • A control board fault
    • Food wrapped so tightly that steam cannot reach the sensor

    What we do

    Our technician cleans the opening in front of the sensor, measures the humidity sensor itself and confirms the control is reading it. A failed sensor is replaced, and our technician explains how to cover food so that the sensor can do its job.

  • Child lock will not releaseThe display reads LOC and the oven ignores input. On most models, holding the stop or lock key for three seconds releases it. If that does not work, the keypad may be at fault.

    Usual causes

    • The lock was engaged accidentally
    • A key stuck in the pressed position
    • A control fault
    • An unlock sequence that does not match the model

    What we do

    Our technician releases the lock using the sequence specified for your model and checks every key for one that is held down. Should the lock still refuse to clear, the faulty keypad or board is renewed and normal operation is confirmed.

  • Interior enamel chipping or rustingThe coating inside the cavity is flaking or showing rust. Exposed metal can cause arcing. Small areas can be restored with a paint made for microwave interiors.

    Usual causes

    • Long-term exposure to steam and heat
    • Abrasive cleaning products
    • Rust developing from spills
    • Arcing that has burned away the coating

    What we do

    We sand small damaged areas and recoat them with microwave-safe enamel, allowing it to cure fully before use. Where peeling or rust is extensive, our technician explains whether replacing the appliance is the more sensible choice.

Brands

Microwave manufacturers we service

All brands →
  • Samsung
  • LG
  • Whirlpool
  • GE Appliances
  • Maytag
  • Bosch
  • KitchenAid
  • Frigidaire
  • Viking
  • Kenmore
  • Amana
  • Electrolux
  • Miele
  • Thermador
  • Wolf
  • Admiral
  • Avanti
  • Blomberg
  • Dacor
  • Fisher & Paykel
  • Gaggenau
  • Hotpoint
  • Insignia
  • JennAir
  • Roper
  • Sharp
  • Smeg
  • Thor Kitchen

Technical notes

Microwaves in Houston kitchens

Over-the-range, built-in and drawer microwaves are the ones worth repairing, because they cost real money and labor to replace. A countertop model that stops heating is usually cheaper to replace than to repair, and we will say so on the phone if that is what you describe.

An over-the-range unit also does the work of a range hood. Above a busy cooktop its vent fan carries heat, steam and grease through the filters, so a clogged grease filter or a tired vent motor is a common call alongside the heating faults: magnetron, high-voltage diode, capacitor and door interlock switches.

Ducted or recirculating vents

Some over-the-range microwaves exhaust outdoors through a wall or roof duct; many in condos and townhomes recirculate through a charcoal filter. A recirculating unit needs its charcoal filter replaced periodically, and a ducted one needs its damper to open freely. A vent fan that switches itself on during cooking is often the thermal protection responding to heat from the burners below, not a fault.

Door interlocks are safety parts

A microwave that will not start, or blows its fuse the moment the door closes, usually has a failed door interlock or monitor switch. These switches exist to stop the magnetron running with the door open. We replace them with the parts specified for the model and test the whole interlock chain, because this is the one fault that should never be bypassed.

What is safe to check, and what is not

With the microwave unplugged or its breaker off, you can clean or replace the grease filters, change the charcoal filter on a recirculating over-the-range unit, and check that the door closes squarely. Everything behind the outer cabinet is off limits: the high-voltage capacitor can hold a dangerous charge after the unit is unplugged. Stop using a microwave that sparks, runs with the door open, smells of burning or trips the breaker.

Door switches, fuses, turntable motors, keypads, lamps and vent parts are the modest repairs. Magnetrons, high-voltage diodes and capacitors cost more, and control boards and trim kits on built-in models the most. On a basic countertop model, any high-voltage repair usually costs more than a new microwave.

Questions

Microwave questions we hear often

Is a built-in microwave or microwave drawer worth repairing?

Usually, yes. Built-in units sit in a trim kit or a cabinet cut-out sized for that model, and drawer microwaves are expensive to replace. A failed magnetron, diode, door switch or touch panel is normally a sensible repair. We give you the price once the fault is confirmed so you can compare.

My microwave trips the breaker or blows its fuse. Is it dangerous?

Stop using it. A blown fuse or tripped breaker usually means a failed door interlock or monitor switch, or a shorted high-voltage capacitor, diode or magnetron. The capacitor can hold a dangerous charge even unplugged, so leave the cabinet closed and let the technician discharge and test it.

Why does my microwave hum loudly but not heat?

A loud hum or buzz with no heating usually means the high-voltage circuit is trying to run and failing: a magnetron at the end of its life, a shorted diode or a failing capacitor. It is a common and repairable fault on built-in and over-the-range units.

Can I keep using a microwave with peeling paint inside?

Not if bare metal is showing near where food sits or if it sparks. Peeling cavity coating can arc and burn through. Small chips away from the waveguide can sometimes be repaired with the manufacturer's cavity paint; widespread peeling usually means replacement.

Arrange a microwave repair

Tell us whether it's over-the-range, built-in or a drawer, the model number and what happens when you press start. We'll confirm a three-hour window.

Call, any hour(832) 476-8009Book on the web