Jump to main content

Appliance repair across Greater Houston

Dishwasher repair in Houston, from standing water to cloudy glasses.

A dishwasher that stops cleaning usually has a clogged filter, a blocked spray arm or a stuck diverter, not a dead pump. We check the inexpensive causes first.
  • Fault found before any price
  • One fixed price you approve
  • 90-day parts warranty

Free to request · 3 steps

Request a repair appointment

Takes about a minute. There is no charge to submit a request.

Prefer to call?(832) 476-8009
Step 1 of 3: Appliance and fault

Appliance and fault

01Which appliance needs attention?
02What is it doing?
Diagnosis
The cause is identified before any price is given
Approval
One fixed price, and work begins only with your consent
Hours
Our phones are answered 24 hours a day
Warranty
Parts warranted for 90 days, labor for 30
1–2 hours
Usual duration of a visit
30
Dishwasher faults documented
27
Manufacturers serviced
24/7
Phones answered

Dishwasher problems

Dishwasher faults we diagnose

Select what your dishwasher is doing. Each card lists the usual causes and how we narrow them down.

  • Dishes come out dirtyThe cycle appears to run as usual, yet food remains on the plates and glassware feels gritty. In nearly every case the water is either reaching the dishes without enough pressure or is too cool to break down grease.

    Usual causes

    • A food-packed filter restricting water to the wash pump
    • Spray arm jets plugged with seeds, glass fragments or scale
    • A weakened wash motor or a worn pump impeller
    • Water failing to reach its proper wash temperature
    • Items loaded in a way that stops the spray arms turning

    What we do

    Our technician removes and cleans the filter and both spray arms, then measures pump output and water temperature while a wash is in progress. A failed pump or heater is replaced, and a test load confirms the dishes come out clean.

  • Standing water in the tubOpening the door reveals cloudy water sitting in the bottom of the tub. A blocked filter or drain hose is the usual reason. If a garbage disposal was installed recently, its knockout plug may never have been removed.

    Usual causes

    • Food debris clogging the filter and sump
    • A kink in the drain hose beneath the sink
    • A blocked dishwasher inlet on the garbage disposal
    • Broken glass jamming the drain pump impeller
    • A clogged air gap fitting on the sink

    What we do

    We clean out the filter and sump first, then inspect the drain hose, the air gap and the disposal connection. A jammed drain pump is cleared, a failed one is replaced, and drainage is tested before we finish.

  • Leaking onto the floorWater collects beneath the door or along the front of the machine. Even a modest leak can damage cabinetry and wood flooring in a short time. It helps to note whether the water appears while the machine is filling, washing or draining.

    Usual causes

    • A torn or worn door gasket
    • A failing seal on the pump
    • A loose inlet valve or hose connection
    • Excess detergent producing foam
    • A machine that is not sitting level

    What we do

    To pinpoint the source, our technician removes the kick plate and watches the base under a light while a cycle runs, noting where water first appears. Whichever part is at fault, whether the gasket, the pump seal, a valve connection or a hose clamp, is renewed. The machine is then leveled across its width and run again to make sure no water reaches the base.

  • Dishwasher will not startThe panel may light without the cycle beginning, or the machine may show no sign of power at all. Before calling, make sure the door is properly latched and the child lock is disengaged, and look at the circuit breaker and any wall switch beneath the sink.

    Usual causes

    • A door latch switch that does not close
    • Child lock left engaged
    • A blown thermal fuse in the control
    • A failed control board
    • No power reaching the unit from the switch or breaker

    What we do

    Diagnosis begins at the junction box beneath the machine to confirm that power is present. From there our technician works through the door latch switch, the thermal fuse on the control and the keypad, one after another. Replacing the component that breaks the start circuit restores operation, which we confirm by running a brief rinse from start to finish.

  • Dishes still wet after cycleA little moisture left on plastic is expected, because plastic retains less heat than glass or ceramic. When every item is wet, though, the drying stage is likely not doing its job. The level of rinse aid also has a strong effect on results.

    Usual causes

    • A burnt-out heating element
    • An empty rinse aid reservoir
    • A vent or drying fan that fails to open on condensation-dry models
    • A failed high-limit thermostat
    • The heated dry setting switched off

    What we do

    Our technician checks the heating element by measuring its resistance, tests the high-limit thermostat, and watches at the close of the cycle to see whether the vent or drying fan operates. Rinse aid delivery is verified too. Faulty parts are renewed, and a load dried on the heated setting shows whether the problem is resolved.

  • Door will not latchThe door either fails to click closed or springs back open after you push it. The dishwasher will not run until the latch is fully engaged, so this stops the machine entirely. An item protruding from a rack is sometimes the reason.

    Usual causes

    • A broken door latch
    • A bent strike plate
    • A rack not pushed fully into the tub
    • A tub pulled out of square by loose mounting

    What we do

    We examine how the door meets the tub and whether the latch mechanism engages. When the latch itself is broken we fit a new one, and a machine that has worked loose from the countertop is fastened back in place.

  • Grinding or rattling while runningGentle swishing and a steady hum are part of normal operation. Grinding, rattling or an unusually loud hum are not. New noises nearly always come from the pumps or the spray arms.

    Usual causes

    • Glass or a bone caught in the pump
    • A spray arm striking a tall item
    • Worn bearings in the wash pump
    • A noisy drain pump
    • Loose mounting hardware

    What we do

    Our technician removes the kick plate and isolates each possible source in turn, listening at the wash pump, then the drain pump, then the spray arms during a cycle. Foreign objects in the pump housing are taken out. When the bearings in the wash pump are worn, the motor is replaced, and any loose bracket is secured so the tub stops vibrating against the surrounding cabinets.

  • Not filling with waterThe motor can be heard, but little or no water enters the tub. First confirm that the supply valve beneath the sink is turned fully on. When it is, a stuck inlet valve or float switch becomes the most likely explanation.

    Usual causes

    • A failed solenoid on the inlet valve
    • A clogged screen in the inlet valve
    • A float switch stuck in the raised position
    • A kinked supply line or a closed shutoff valve

    What we do

    When the control calls for water, our technician measures both supply pressure and voltage at the inlet valve. The valve screen is cleared of debris, the solenoid is checked for continuity, and the float is examined to see whether its plunger moves freely. After the failed component is renewed, the water level is compared with the fill mark inside the tub.

  • Persistent bad odorA sour or rotting smell almost always comes from food that has been trapped somewhere in the machine. Grease and debris tend to gather in the filter, around the door seal and along the drain path, and the odor tends to be stronger in warm weather.

    Usual causes

    • A dirty filter retaining food
    • Water remaining in the sump between cycles
    • A drain hose without a high loop, allowing sink water to flow back
    • Grease and food lodged in the door gasket
    • Backflow from the disposal connection

    What we do

    Cleaning the filter, sump and door gasket comes first, followed by a hot cycle with a purpose-made dishwasher cleaner. Our technician also confirms the drain hose has a high loop or air gap; without one, dirty sink water can siphon into the tub, a frequent source of odor that is easy to overlook. If a drain fault is leaving water in the sump, it is repaired.

  • Detergent cup stays closedAfter the cycle, the pod or powder is still in the dispenser. Because the detergent was never released, the dishes cannot be cleaned properly. A sticking latch or a failed actuator is usually responsible.

    Usual causes

    • A broken dispenser latch
    • A failed actuator coil
    • Hardened detergent around the cup
    • Tall items blocking the dispenser door

    What we do

    After cleaning the cup and latch, our technician triggers the dispenser from the service test mode to confirm whether the actuator moves. A latch that sticks or an actuator coil that has burnt out is resolved by fitting a new dispenser assembly. We also look at whether tall items in the lower rack are in the way and show you where to place them.

  • White film or spotsGlassware emerges cloudy or marked with white spots. Where the supply is on the hard side, calcium and magnesium dry onto the glass and gradually coat the interior of the machine as well; too much detergent or an empty rinse aid reservoir produces a similar film.

    Usual causes

    • Hard water mineral deposits
    • An empty rinse aid reservoir
    • Using too little or too much detergent
    • Wash water that is not hot enough

    What we do

    Our technician measures the wash water temperature and reviews how the rinse aid dispenser is set. The interior is then descaled, and we advise on a detergent and rinse aid suited to the hardness of your water supply.

  • Stops partway through cycleThe cycle ends early with flashing lights, or the machine simply falls silent. Many dishwashers are designed to halt when they detect a fault, and a door switch or a sensor is frequently the trigger.

    Usual causes

    • A door switch losing contact
    • Overheating or a failed thermostat
    • A tripped leak sensor
    • A fault in the control board

    What we do

    Stored fault codes are retrieved first, and then a cycle is observed so the precise point of shutdown can be identified. The component tied to that stage, such as the door switch, a thermostat, the leak float or the board, is tested and renewed if it fails. Before leaving, our technician lets a complete cycle run through.

  • Drain pump not workingAt the end of the cycle the machine hums, but the water does not leave the tub. When the filter and hose are both clear, the drain pump itself has likely jammed or failed.

    Usual causes

    • Glass or bone jamming the impeller
    • A burnt-out pump motor
    • Damaged wiring to the pump
    • A check valve stuck shut

    What we do

    While the control is calling for drain, our technician confirms whether voltage is reaching the pump. The pump is then removed so its impeller and check valve can be inspected. Debris jamming the impeller is cleared, and a pump whose motor has burnt out is replaced. Finally, a drain test shows whether the sump empties completely.

  • Clogged dishwasher filterOn many models you unscrew the filter from the bottom of the tub by hand. Once it becomes clogged, cleaning results suffer, the tub drains slowly and unpleasant odors develop.

    Usual causes

    • Grease and food packed into the mesh
    • A filter that has never been cleaned
    • Broken glass caught in the sump
    • A cracked fine filter letting debris through to the pump

    What we do

    Both the coarse and fine filters are taken out and cleaned, and the sump below them is flushed. If a filter is cracked we replace it, because debris passing through will eventually damage the pump. Our technician will also show you how to remove the filter yourself; cleaning it every few weeks prevents most of these problems.

  • Wash pump not sprayingWater enters the tub, but there is little sound of spraying and the dishes stay dirty. The wash pump is what drives water through the spray arms, so when it fails, no cleaning takes place.

    Usual causes

    • A failed wash motor
    • A broken impeller
    • A failed motor start capacitor
    • Debris lodged in the pump

    What we do

    Our technician listens to the motor and tests its windings, and on older models also checks the start capacitor. Opening the pump housing reveals whether the impeller is broken or something is trapped inside. A new motor or impeller is fitted where needed, and the spray arms are observed during a wash to confirm pressure has returned.

  • Spray arms blocked or stuckWhen the spray arms are obstructed or cannot rotate, dishes in one part of the rack may stay dirty while the rest come out clean. Food particles and hard-water scale readily block the small jets.

    Usual causes

    • Jets blocked by mineral scale
    • A cracked spray arm bearing
    • An item obstructing the arm
    • A loose spray arm hub

    What we do

    Both spray arms are removed, each jet is cleared with a fine pick, and scale and seeds are rinsed out. Our technician inspects the hubs and bearings, renewing any that are cracked or worn. Once refitted, the arms are rotated by hand to be sure no rack component obstructs them.

Show 14 further dishwasher faults
  • Heating element not workingThe heating element raises the water temperature during the wash and assists with drying. Without it, plates finish damp with a greasy film, and some cycles stall because the water never reaches the required temperature.

    Usual causes

    • An element that has burnt open
    • A failed high-limit thermostat
    • A thermistor reporting an incorrect temperature
    • A failed heater relay on the control board

    What we do

    The element is checked by measuring its resistance, and the high-limit thermostat and thermistor are tested alongside it. Should all three be sound, our technician monitors the heater relay on the control board while a cycle runs. Once the failed part is renewed, the water temperature is taken partway through a wash to confirm proper heating.

  • Control board faultThe touchpad stops responding, or the dishwasher starts and stops unpredictably. We test the board last, because a number of other faults can produce the same behavior.

    Usual causes

    • Damage from a power surge
    • Water from a leak reaching the board
    • A burnt relay or circuit trace
    • A failed keypad sending false inputs

    What we do

    Our technician first eliminates the door switch, the keypad and the wiring as possible causes, then checks each board input and output against the schematic. A board confirmed as faulty is replaced. We then trace the leak or electrical surge responsible for the damage, so the new board is not exposed to the same problem.

  • Cycle running far too longOn newer models a normal cycle can run two hours or longer. If the time has grown noticeably beyond what is usual for your machine, it may be waiting for water to heat or repeating a fill that did not complete.

    Usual causes

    • A weak or failed heater
    • Cold water arriving at the machine
    • A turbidity sensor adding extra rinses
    • Slow filling from a clogged inlet screen

    What we do

    Each phase of the cycle is timed, and the temperature of the hot water at the kitchen tap is measured. Our technician tests the heater and thermistor and clears the inlet screen if filling is sluggish. Once the cause of the delay is repaired, we may suggest letting the kitchen tap run hot for a moment before you start a cycle, particularly when the water heater is far from the kitchen.

  • Error code displayedA flashing light or a displayed code indicates which system the dishwasher has flagged, such as draining, filling or heating. The code narrows the search, but the component behind it still has to be tested.

    Usual causes

    • A blocked drain
    • A tripped leak sensor
    • A heater or sensor fault
    • A door switch fault

    What we do

    Our technician reads both the current code and the stored history, then runs the manufacturer's service test for the system it points to. The part involved, which may be a pump, a valve, the heater, a switch or the float, is checked and renewed if it fails. After the code is cleared, the machine is monitored through a full cycle.

  • Leak at the doorWater drips from beneath the door. A worn door gasket or an overfilling tub is often responsible, and the wrong type of detergent can generate foam that escapes past the seal.

    Usual causes

    • A torn or flattened door gasket
    • Door hinges out of adjustment
    • Overfilling caused by a sticking valve
    • Excess foam from unsuitable detergent
    • A machine not level from side to side

    What we do

    The full length of the gasket is inspected, the door's alignment is checked and the water level is observed while the tub fills. Our technician renews a worn gasket and adjusts the hinges and leveling feet as needed. If the tub is overfilling, the responsible valve or float is identified and corrected.

  • Leak sensor stopped the cycleMany models have a float sitting in the base pan that shuts the machine down when water gathers there. The cycle halts and a code appears. The leak that raised the float still needs to be located.

    Usual causes

    • A leaking hose letting water into the base pan
    • A leak at the pump seal
    • Foam overflowing into the base
    • A loose inlet fitting

    What we do

    Our technician opens or tilts the base to locate the source of the water, dries the pan and resets the float. The leaking component, whether a seal, a hose or a fitting, is renewed, and a full cycle is then run to confirm the float does not rise again.

  • Water level too highWater rises to the edge of the door or keeps entering after the fill should have ended, and this can lead to a flooded kitchen. Until a repair is made, keep the dishwasher's water turned off at its shutoff valve and do not run another cycle.

    Usual causes

    • An inlet valve stuck open
    • A float switch stuck in the lowered position
    • A failed pressure sensor
    • A control board failing to close the valve

    What we do

    With power disconnected, our technician watches whether water continues to enter; if it does, the inlet valve is stuck open. The float and the pressure sensor are tested as well. After the faulty valve or switch is renewed, the water level is verified on the next cycle.

  • Hums but will not washThere is a humming sound but no spraying. Power is reaching the motor, yet it cannot turn, either because something is jamming it or because the part that starts it has failed.

    Usual causes

    • A seized wash motor
    • Debris jamming the impeller
    • A failed start capacitor
    • Worn motor bearings

    What we do

    The pump is opened so any glass or fruit pits blocking the impeller can be removed, after which our technician tests the motor and its capacitor. A motor that has seized or burnt out is replaced, and a test run confirms the pump it comes up to speed freely.

  • Upper rack stays dirtyThe lower rack comes out clean while the upper rack does not. The upper spray arm or its water feed is probably obstructed, and a rack that is not seated correctly can also cut off the water supply.

    Usual causes

    • A clogged upper spray arm
    • The rack not connecting to the water feed
    • A cracked feed tube
    • Tall items in the lower rack blocking the arm

    What we do

    Our technician cleans the upper spray arm, checks its feed tube for cracks and confirms the rack connects properly with the water inlet at the back of the tub. Any broken arm or cracked tube is renewed, and we explain how to arrange the upper rack so the spray can reach every item.

  • Water from the sink air gapWhen the dishwasher drains, water overflows from the small chrome cap beside the faucet. This indicates a blockage in the air gap itself or in the hose leading to the disposal.

    Usual causes

    • Food lodged in the air gap
    • A blocked disposal inlet
    • A kink in the hose from the air gap to the disposal
    • A partially blocked sink drain

    What we do

    After removing the cap, our technician clears the air gap chamber and flushes the hose that runs to the disposal. The inlet on the disposal is inspected for buildup, and a drain cycle confirms that water now flows into the drain instead of back into the sink.

  • No drain after new disposalA newly installed garbage disposal comes with a knockout plug sealing its dishwasher inlet. Unless that plug is removed, the dishwasher has nowhere to drain.

    Usual causes

    • The knockout plug never removed
    • An overtightened hose clamp
    • A hose pinched behind the disposal
    • A clogged disposal inlet

    What we do

    The drain hose is disconnected so our technician can punch out the plug in the disposal inlet and remove the loose piece from inside the grinding chamber. The hose is then reattached with a correctly sized clamp, and a drain test is run so you can see the water clear.

  • Rinse aid not dispensingThe rinse aid level does not drop for months, or dishes come out spotted and wet. The dispenser may be sticking, or its setting may be too low.

    Usual causes

    • A sticking dispenser cap or valve
    • A dispenser setting that is too low
    • A failed actuator
    • A cracked, leaking dispenser

    What we do

    Our technician checks the dispenser cap and its setting, then operates the actuator from the service test mode. A dispenser that is faulty or leaking is replaced, and the dosage is set to suit how hard your water is.

  • Door drops or will not holdThe door falls open heavily or will not stay where you leave it. One of the springs or cables on either side has probably broken, and a sharp snap is often heard when it happens.

    Usual causes

    • A broken door spring
    • A cable that has snapped or slipped off its pulley
    • A worn hinge
    • A loose spring link

    What we do

    Springs or cables are replaced on both sides together so the door stays evenly balanced. Our technician also inspects the hinges and pulleys for wear, then opens and closes the door repeatedly to confirm it holds at any angle.

  • Control buttons not respondingSome or all of the control panel buttons have stopped working. Moisture and steam can damage the touchpad over time, and an engaged control lock produces the same symptom.

    Usual causes

    • A failed touchpad membrane
    • The control lock switched on
    • A loose ribbon cable
    • A failed control board

    What we do

    Our technician begins by confirming the control lock is not engaged, then tests every key and the ribbon cable where it joins the board. The failed touchpad or board is renewed, and each key is checked again before the panel is closed.

Brands

Dishwasher manufacturers we service

All brands →
  • Samsung
  • LG
  • Whirlpool
  • GE Appliances
  • Maytag
  • Bosch
  • KitchenAid
  • Frigidaire
  • Viking
  • Kenmore
  • Amana
  • Electrolux
  • Miele
  • Thermador
  • Admiral
  • ASKO
  • Bertazzoni
  • Blomberg
  • Dacor
  • Fisher & Paykel
  • Gaggenau
  • Hobart
  • Hotpoint
  • JennAir
  • Roper
  • Smeg
  • Thor Kitchen

Technical notes

Dishwashers in Houston kitchens

Water across the Houston area is moderately hard in many neighborhoods, and it varies with the supply: City of Houston water is mostly treated surface water, while many suburbs draw on groundwater or a MUD system. Where it runs hard, it shows up as white film on glasses, scale on the heating element and spray-arm nozzles that slowly close up.

The other common thread is drainage. A dishwasher shares its drain with the sink and often a garbage disposal, so a clogged air gap, a new disposal with its knockout plug still in place, or a high loop that has slipped can all leave water in the tub. We test the drain path before condemning the pump.

Hard water, rinse aid and the hardness setting

Many dishwashers, especially European models, have a water-hardness setting or a salt reservoir that leaves the factory set for nobody's house in particular. Matching it to your supply, keeping rinse aid topped up and using the right amount of detergent clears most cloudy-glass complaints. Your water provider's annual water quality report often lists hardness.

Leaks you can't see yet

A slow dishwasher leak can run under the cabinets and into the flooring of a slab-built kitchen long before it shows. If the floor by the toe kick feels soft or you see water at the door, close the supply valve under the sink. Models with a leak sensor in the base lock out with an error code when water reaches it; the sensor is usually right, and we find the water before resetting it.

What to try first, and what decides the cost

Clean the filter under the lower spray arm, check that the spray arms spin freely and their holes are clear, and confirm the sink and any garbage disposal drain normally. Damp plastics on a model that dries by condensation are expected, not a fault. Close the supply valve under the sink and stop running cycles if water appears at the toe kick or the floor in front of the dishwasher feels soft.

Inlet valves, door gaskets, float switches and drain hoses are minor repairs. Drain and circulation pumps sit in the middle, and a control board costs more; on many European models the water heater is built into the circulation pump, so the two are priced as one part. A tub that leaks through rust or a cracked base is rarely worth repairing.

Questions

Dishwasher questions we hear often

Why is there standing water in the bottom after the cycle ends?

Start with the filter under the lower spray arm, which catches food and is the most common cause. After that, the usual suspects are a kinked drain hose, a clogged air gap on the sink, a disposal whose knockout plug was never removed, and finally the drain pump itself. We work through them in that order.

What causes a bad smell from my dishwasher?

Food trapped in the filter, standing water in the sump and a drain hose without a high loop that lets sink water flow back are the usual causes. Keeping the door closed in a humid kitchen between loads makes it worse. Clean the filter, run a hot cycle with a dishwasher cleaner, and call us if the smell or standing water returns.

Do you repair dishwasher drawers and panel-ready models?

Yes, including drawer dishwashers and panel-ready models hidden behind cabinet fronts. Both take more care to remove and reinstall without damaging the panels or countertop, and we allow for that time when you give us the model number at booking.

Is it normal for a dishwasher cycle to take two hours or more?

On many current models, yes. Energy-efficient machines use less water and a lower temperature over a longer cycle, and sensor cycles add time for heavily soiled loads or cool incoming water. A cycle that keeps getting longer, or one that never finishes, is worth a diagnosis.

Book a dishwasher repair

Tell us the brand, the model number and whether it's leaving water, leaking or not cleaning. We'll set a three-hour window and bring the matching parts.

Call, any hour(832) 476-8009Book on the web