Induction cooking works on a different principle from gas or radiant electric cooking, and that difference explains many of the messages an induction cooktop displays. Before treating a code as a fault, it is worth understanding how the cooktop decides whether to heat at all.
How induction heats
Beneath each cooking zone is a copper coil. When the zone is switched on, the electronics pass a rapidly alternating current through the coil, which produces an alternating magnetic field. If a suitable pan sits on the glass, that field induces currents in the pan's base, and the pan itself becomes hot. The glass warms mainly from contact with the hot pan.
Two consequences follow. First, the pan must be made of a material that responds to the magnetic field. Second, the cooktop is constantly checking whether a suitable pan is present, and it will refuse to heat, or will show a symbol, if it does not find one.
Pan compatibility
The magnet test
Touch an ordinary magnet to the underside of the pan. If it holds firmly, the pan will normally work on induction. If it does not hold, or holds only weakly, the pan is unlikely to heat well. Cast iron, enameled cast iron and many stainless steel pans pass. Aluminum, copper, glass and some stainless steel pans do not, unless they have a magnetic plate bonded to the base.
Many manufacturers also mark compatible cookware with an induction symbol, usually a coil shape, on the base or packaging.
Size, shape and flatness
A pan can be magnetic and still fail to register.
- Base diameter. Each zone has a minimum pan size. A small saucepan or espresso pot on a large zone may not be detected. The manual lists minimum diameters.
- Flat base. A warped or domed base makes poor contact and may cause the zone to cycle, buzz or switch off.
- Position. Center the pan over the zone markings. An off-center pan may not be sensed.
- Bridged and flexible zones. On cooktops with flexible areas, the control decides which coils to energize from the pan's footprint. An unusual shape, such as a long griddle, may require the bridge function described in the manual.
Some humming or buzzing at high power is normal, particularly with layered or lightweight pans. A loud rattle, or a sound that changes when you move the pan, usually comes from the cookware rather than the cooktop.
Categories of error message
The exact codes differ between manufacturers and even between models of the same brand, so the manual for your model is the only reliable key. Most messages, however, fall into a few general groups.
No pan, or unsuitable pan
Often shown as a flashing symbol, a flashing power level or a letter on the zone display. The cooktop is saying it cannot find a suitable pan. Check compatibility, size and position before anything else. If the message appears on one zone with a pan that works on every other zone, the fault may lie in that zone's coil or its electronics.
Overheating
Induction electronics generate heat and are cooled by a fan beneath the glass. If they become too hot, the cooktop reduces power or shuts a zone down and may show an overheating message. Causes include a blocked ventilation path, a cooktop installed without the clearance its instructions require, a drawer packed tightly beneath it, or a fan that has failed. An empty pan left on high can also trigger protection. In a hot kitchen on a summer evening, with the oven running below and the cooling fan drawing warm air, an older or cramped installation can reach that limit sooner than it would in winter.
Control panel and touch sensors
Water, spilled food or a pan resting on the controls can make touch controls register a continuous press. Many cooktops then shut down or lock and display a code. Wipe the panel dry and remove anything resting on it. Steam from a large pot of boiling water, or condensation forming on the glass in a humid kitchen, can do the same thing; dry the controls with a towel before assuming a fault.
Power supply and internal faults
Some codes refer to supply voltage, communication between boards, a temperature sensor or the power module itself. Power flickers and brownouts during summer storms, or when service is restored after an outage, can leave a cooktop showing a supply or communication code that clears after a breaker reset. If such a code persists after the cooktop has been switched off at the breaker for a few minutes and restored, a technician needs to test the components.
What you can safely check
- Confirm the pan passes the magnet test and meets the minimum size for the zone.
- Try a known good pan on the same zone, and the problem pan on a different zone.
- Clean and dry the glass and the touch controls.
- Make sure the lock function, often labeled as a child lock, has not been switched on.
- Make sure nothing blocks the cooktop's ventilation openings or crowds the space beneath it.
- Switch the cooktop off at its circuit breaker for several minutes, then restore power.
Do not remove the glass or open the cooktop. The electronics carry mains voltage and hold stored charge after power is removed.
Safety notes
If the glass is cracked, switch the cooktop off at the breaker and do not use it until it has been inspected, since liquid can reach the electronics through the crack. Manufacturers advise people with pacemakers or other implanted medical devices to consult their physician or the device maker about using induction cooktops.
What a technician does
Our technicians read the code against the manufacturer's service information for your model, test the coil, temperature sensors, cooling fan and power and control boards, and check the installation for ventilation and supply voltage. Before any work starts you receive one fixed price to approve, with the diagnostic fee credited toward it.
You can learn more about our cooktop repair service or book a visit.